Manual de uso Vivanco UR 89 Control remoto

Manual de uso

UR 89 Universal Controller

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: hotline@vivanco.de 1

(GB) Instructions

Vivanco UR 89 remote control for almost

all TV, audio, video and other infrared-

controllable equipment

Inserting the batteries

Open the battery flap on the back of the

remote control, press the tongue lightly

upwards, then insert 2 alkaline AAA batteries.

Check that the polarity markings on the

batteries and in the battery compartment are

correctly lined up (+=+), then close the flap

carefully. – Always use undamaged batteries.

Adapting to appliances

In order to control your appliances you must

adapt or set the remote control to them. There

are two ways of doing so: direct control code

entry or code search.

If your UR 89 does not understand you it

blinks twice several times and you can then

repeat the entry. Each understood entry is

confirmed by an appliance button blinking

once briefly.

Direct control code entry using the

enclosed list

Example: setting to control a Panasonic

television set:

1. The enclosed list gives, for example, the

Panasonic Code 154.

Please make sure you have selected the

correct list for television sets (TV).

2. To prepare code entry, press the SET

button, bottom right, keep it pressend and

then press the required appliance button, e.g.

TV, additionally until the lamp (LED) lights

constantly.

3. Then press the number buttons (e.g. 1 5

4) in sequence.

4. Once the numbers have been entered

the button lamp goes out and the remote

control is ready to control your appliance.

5. Finally, test the control code setting by

trying to control (in this example) your

television set. If it does not work at all or not

correctly try a different code from the list or

the code search (see below).

6.

To set the remote control for other

appliances, proceed in the same way. Instead

of the TV appliance button, press another

button (e.g. VCR, CBL/SAT(DVB,

DECODER), DVD, TUNER, TAPE, CD,

AMP).

Code search

If the brand of your appliance is not in the list

or none of the codes given fits, we

recommend a code search.

Manual code search

1. Switch on the appliance to be controlled.

Program is running.

2. To prepare code search, press the SET

button, bottom right, keep it pressend and

then press the required appliance button, e.g.

TV, additionally until the lamp (LED) lights

constantly.

3. Then point the remote control at the

appliance to be controlled.

4. Briefly press the ON/OFF

(appliance on/off) button once. The lamp

(LED) blinks. – Except when searching for a

TV code you can also briefly press the yellow

> (Play) button and use the Play function to

search. Make sure that a tape, a DVD or a CD

is inserted in the tape deck, player or

recorder.

5. Press the ON/OFF (appliance

on/off) or Play button repeatedly, approx.

every second, until the appliance, e.g. your

DVD player, reacts. - If you notice the reaction

of your appliance too late and the next code

has already been emitted you can go back by

pressing SET and then ON/OFF or Play

again. If your appliance has switched itself off

you must switch it back on again, e.g. on the

appliance or with the original remote control,

to continue searching. - When your appliance

reacts you can also try out other buttons

without interrupting the search. If some

buttons do not work properly, simply continue

searching with ON/OFF or Play.

6. When your appliance reacts correctly,

press the appliance button, e.g. TV, and end

the search. The lamp (LED) goes out.

- The UR 89 continues with the search at the

point where you interrupted it. When the end

of the code list is reached the search stops

automatically. The remote control blinks

quickly several times. The code last entered

remains stored. The search stops after

approx. 30 seconds of inactivity.

Automatic code search *

Your remote control finds the correct settings

almost automatically in seconds:

1. Switch on the appliance to be controlled.

A channel number, for example, appears in

the display of your satellite receiver.

2. To start the code search, press the SET

button, bottom right, and then additionally the

required appliance button, e.g. TV, for more

than 3 seconds until the lamp (LED) starts to

blink.

3. Then point the remote control at the

appliance to be controlled while the remote

control emits a different ON/OFF signal every

2 seconds.

4. When your appliance reacts, press any

button, except SET, to end the search. – If

you ended the search too late, continue to

search using the Manual Code Search (see

above).

5. Finally, test the control code setting by

trying to control, for example, your DVD

appliance. If it does not work correctly, please

try the code search again. The code search

then begins with the next code in the

sequence. - Remember to switch your

appliance, e.g. DVD, back on again if you

wish to continue searching.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Vivanco UR 89 Control remoto. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Vivanco. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Vivanco UR 89 Control remoto en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Vivanco Controles remotos
Más manuales de Controles remotos

Preguntas frecuentes sobre Vivanco UR 89 Control remoto

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Vivanco Viv.Control 3 Control remoto

Manual de uso

Vivanco UR 03 UF Control remoto

Manual de uso

Vivanco UR Zap 2 Control remoto

Manual de uso

Vivanco UR Z2 Control remoto

Manual de uso

Vivanco UR 100 LCD Control remoto

Manual de uso

Vivanco UR 40 USB Control remoto

Manual de uso

Vivanco UR 820 LCD Control remoto

Manual de uso

Vivanco UR 2 Control remoto

Categorias relacionadas