Manual de uso Aspes AAS3012B Aire acondicionado

Manual de uso

1.Insertfromoutsidetheroomcableintoleftside of thewall

hole, in w hich the pipe has already existed.

2. Pull out the cable on the front side, and connect the cable

making a loop.

Insertthecablefromtheback

ƽ

side of the unit, then pull it out

on the front side.

Loosen the screws and insert

ƽ

the cable ends fully into

terminal block, then

tighten the screws.

Pull the cable slightly to

ƽ

make sure the cables have

been properly inserted and

tightened.

After the cable connection,

ƽ

never fail to fasten the connected cable with the

wiring cover.

When connecting the cable after installing the indoor unit

When connecting the cable before installing the indoor unit

Note:

To Outdoor unit

Code

indication

Trouble description

Analyze and diagnose

E1

E2

E4

E7

E14

Heat-exchange

sensor failure

Indoor EEPROM

error

Communication

fault between

indoor and outdoor

units

Indoor fan motor

malfunction

Operation halt due to breaking

of wire inside the fan motor;

Operation halt due to breaking

of the fan motor lead wires;

Detection error due to faulty

indoor unit PCB;

Indoor unit- outdoor unit signal

transmission error du

e to wiring

error;

Faulty PCB;

Faulty EEPROM data;

Faulty EEPROM;

Faulty PCB;

Faulty connector connection;

Faulty thermistor;

Faulty PCB;

Room temperature

sensor failure

The power source must be exclusively used for air

ƽ

conditioner.

In the case of installing an air conditioner in a moist place,

ƽ

please install

an ea

For installation in other places, use a circuit breaker as far

ƽ

as possible.

Pipecuttingiscarriedoutwith a pipecutterandbursmust beremoved.

After inser ting the flare nut, flaring work is carried out.



Cutting and Flaring Work of Piping

Conventionalflare tool

Clutch-type clutch-type(Rigid-type) Wing-nut type (Imperial-type)

A 0~0.5mm 1.0~1.5mm 1.5~2.0mm

rth leakage breaker.

Lean

Damage of flare Partial Too outside

Correct Incorrect



On Drainage

It becomes

high midway.

The gap with the

ground is too small.

There is the bad

smell from a ditch

It waves.

The end is imm-

ersed in water.

Pleaseinstallthedrainhosesoastobedownwardslopewithoutfail.

Please don’t do the drainage as shown below.

ƽ

ƽ

Please pour water in the drain pan of the indoor unit, and

ƽ

is carried out surely to outdoor.

In case that the attached drain hose is in a room, please

ƽ

apply heat

insulation

to

Less than

5cm

confirm that

drainage

it without fail.

Crack

Indoor unit

CheckItemsforTestRun

Gasleakfrompipeconnecting?

Heat insulation of pipe connecting?

Are the connecting wirings of indoor and outdoor firmly

Is the connecting wiring of indoor and outdoor firmly fixed?

Is drainage securely carried out?

Is the earth line securely connected?

Is the indoor unit securely fixed?

Is power source voltage abided by the code?

Is there any noise?

Is the lamp normally lighting?

Arecoolingandheating(wheninheatpump)performednormally?

Is the operation of room temperature regulator normal?

Please kindly explain to our customers how to

operate

through the instruction manual.

inserted to the terminal block?

Ƶ

Put check mark

in boxes

Flare tooling die

1.Cut pipe

2.Remove burs

3.Insert the flare nut

4.Flare pipe

ƽ

ƽ



On Drainage

Check for Installation and Test Run



7

When connecting the cable, confirm the terminal number of indoor and

outdoor units carefully. If wiring is not correct, proper operation can not

be carried out and will cause defect.

4G1.0mm

2

(Other models)

Connecting wiring

4G1.5mm

2

(AAS3012B)

If the supply cord is damaged, it must be replaced by the manufacturer

or its service agent or a similar qualified person. The type of connecting

wire is H07RN-F.

If the fuse on PC board is broken please change it with the

type of

3.15A/250VAC (Indoor).

The wiring method should be in line with the local wiring standard.

After installation, the power plug should be easily reached.

A breaker should be incorporated into fixed wiring. The breaker should

be all-pole switch and the distance between its two contacts should be

not less than 3mm.

Power Source Installation

Flare tool for R32

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Aspes AAS3012B Aire acondicionado. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Aspes. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Aspes AAS3012B Aire acondicionado en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Aspes Aires acondicionados
Más manuales de Aires acondicionados

Preguntas frecuentes sobre Aspes AAS3012B Aire acondicionado

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Aspes AAAP1200B Aire acondicionado

Manual de uso

Aspes AAS1090 Aire acondicionado

Manual de uso

Aspes AAAP900F Aire acondicionado

Manual de uso

Aspes AAAP1200F Aire acondicionado

Manual de uso

Aspes AAS2024 Aire acondicionado

Manual de uso

Aspes AAS3018B Aire acondicionado

Manual de uso

Aspes AAS2012 Aire acondicionado

Manual de uso

Aspes AAC2024 Aire acondicionado

Categorias relacionadas