Manual de uso BeSafe iZi Twist B Asiento para bebé

Manual de uso

10 11

• Adjustable headrest

• Shoulder straps

• Baby insert

• Baby cushion

• Harness buckle

• Central adjuster

• Reclining handle

• Release handle headrest

• Installation screen

• Spirit level

• Battery compartment

• Floor support

• Floor support height indicator

• Height adjuster floor support

• Rotation release handle

• Switch for ISOfix connectors (2x)

• ISOfix connectors (2x)

• ISOfix release switch

• ISOfix indicators (2x)

• ISOfix car anchorage (2x)

(1a)

(1b)

(1c)

(1d)

(1e)

(1f)

(1g)

(1h)

(1i)

(1j)

(1k)

(1l)

(1m)

(1n)

(1o)

(1p)

(1q)

(1r)

(1s)

(1t)

Preparing to install

Installation

1. When installing in the back seat of the vehicle, push the front seat of

the vehicle forward as far as possible and adjust the back rest into

an upright position (if it can be adjusted).

2. When installing in the front seat of the vehicle, adjust the back rest

into an upright position.

3. Position the vehicle on a horizontal surface when installing the seat.

4. When the base is lifted the floor support should fall downwards from

underneath the base. Do this outside the car.

5. Push down the switch for the ISOfix connectors at both sides to

release the ISOfix connectors. (2)

6. Position the base on the vehicle seat. Click the ISOfix connectors on

to the ISOfix anchorages on the vehicle seat. Make sure that both

ISOfix indicators are green. (3)

7. Push the seat towards the backrest of the vehicle seat until it

touches the backrest. (4)

8. The ISOfix connectors willhave resistance sliding in, in the most

outward positions, before they are connected with the ISOfix

anchorage of the vehicle.

9. Tip: once the ISOfix connectors are installed, the seat can be

turned towards the door of the vehicle to get a better view on the

installation display.

10. Adjust the floor support, so it is in contact with the floor of the

vehicle. (5)

11. The height indicator of the floor support shows green when the floor

support is in contact with the floor. (5)

12. Lift the base at the front side (near the spirit level) and extend

the floor support till the spirit level is in the middle, indicating a

horizontal position of the base. (5)

13. Tip: place one foot onto the bottom end of the floor support while

lifting the base to make adjusting the length at this step easier.

14. The alarm sound stops when the floor support indicators show green

and it is in contact with the floor. Make sure that the horizontal spirit

level shows a horizontal position of the seat. (5)

15. When having the child seat installed rear facing in the back, it is

recommended to position the front vehicle seat in a way that it is

close to the touchpoint with the child seat. Make sure that the child

seat can still rotate freely.

When having the child seat installed rear facing on the passenger

seat in the front, it is recommended to position the passenger seat

in a way that the dashboard is close to the touchpoint with the child

seat. Make sure that the child seat can still rotate freely.

16. Tip: If you feel like the base has too much side movement, you can

install the seat tighter against the vehicle seat backrest. Make the

support leg short, grab the base and push it against the vehicle

backrest with more force. Move it side to side until you hear one

more ‘click’ per side, then lift the base into horizontal position again

17. The seat is delivered with removable SIP+ (side impact protection

+). This extra side impact protection should be used on the door side

of the vehicle. It can be connected by slotting between the seat shell

and the fabric. The seat already oers high level integrated side

impact protection. This extra side impact protection improves the

protection in the side impact still further. (Not on all models) (6)

18. Tip: For an optimal height of the SIP+, position it between the two

raised dots on the side of the seat shell.

19. Do not use the SIP+ on the seat when the space between seat and

door of the vehicle is too small, which might lead to a situation where

the seat is not positioned correctly on the vehicle seat.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus BeSafe iZi Twist B Asiento para bebé. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con BeSafe. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu BeSafe iZi Twist B Asiento para bebé en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para BeSafe Asientos para bebé
Más manuales de Asientos para bebé

Preguntas frecuentes sobre BeSafe iZi Twist B Asiento para bebé

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

BeSafe iZi Go Modular Asiento para bebé

Manual de uso

Maxi-Cosi Mica Pro Eco i-Size Asiento para bebé

Manual de uso

Lorelli Spirit Asiento para bebé

Manual de uso

Maxi-Cosi Coral 360 Asiento para bebé

Manual de uso

Maxi-Cosi Pearl Pro 2 i-Size Asiento para bebé

Manual de uso

Lorelli Ares Isofix Asiento para bebé

Manual de uso

Nuna aace LX Asiento para bebé

Manual de uso

Cybex Solution Z i-Fix Asiento para bebé

Categorias relacionadas