Manual de uso Bionaire BASF1314 Ventilador

Manual de uso

Converting to a table fan -

Model BASF1314 only: On model BASF1314 an

additional short pole (R) is supplied which allows

the fan to be converted into a table fan. To

change to this short pole, remove the fan head

assembly from its position on top of the inner

pole and unscrew the L-shaped locking lever at

the base. Remove the long pole, replace with the

short pole and reassemble as detailed above.

OPERATING INSTRUCTIONS

1. Set the fan base on a dry level surface

2. Make sure the Selector (Speed) Control is in

the OFF position. Selector (Speed) Control is

located on the top of the fan motor housing.

3. Plug the cord into a suitable 220-240V. AC

outlet.

4. The SPEED is adjusted by turning the Selector

(Speed) Control to the desired setting:-

O-III-II-I.

5. The OSCILLATION control is located on the

top of the fan motor housing. To start

oscillation, push the control knob down.

To stop oscillation, pull the control knob up.

ADJUSTMENT

Tilt adjustment

Follow these instructions to tilt the fan head for

upward angle air movement.

1. To change the tilting angle of the fan head,

simply loosen the tilt adjustment knob (J)

2. Move the fan head to the desired angle, then

firmly tighten the knob to lock in place.

Height adjustment

Follow these instructions to adjust the height of

the fan.

1. Turn the pole locking knob (L) anti-clockwise

to loosen the pole.

2. Adjust the pole to the desired height and

firmly tighten the locking knob in a clockwise

direction.

CLEANING AND MAINTENANCE

Follow these instructions to correctly and safely

care for your Bionaire

®

fan. Please remember:-

• Always unplug the fan before cleaning or

assembly.

• Do not allow water to drip on or into the fan

motor housing.

• Be sure to use a soft cloth, moistened with a

mild soap solution.

• Do not use any of the following as a cleaner:

petrol, thinners or benzene.

Fan Blade cleaning

(See instructions for fan head assembly)

1. To access the fan blade, remove the front grill

and securing screw.

2. Clean the fan blade, front and rear grills with

a soft moist cloth.

3. Replace the fan blade, tighten screw and

securely fasten the front grill.

Fan head, base and pole cleaning

Using a soft, moist cloth, with or without a mild soap

solution, carefully clean the fan base, pole and

head. Please use caution around the motor housing

area. Do not allow the motor or other electrical

components to be exposed to water.

FAN STORAGE

Your fan can be stored either partially disassembled

or assembled.

It is important to keep it in a safe, dry location.

• If stored disassembled, we recommend using

the original (or appropriately sized) box.

• If stored assembled or partially assembled,

remember to protect the fan head from dust.

FITTING A REPLACEMENT PLUG (UK

ONLY)

The wires in this mains lead are coloured in

accordance with the following code:

Blue - Neutral

Brown - Live

This appliance is fitted with a 13 amp plug. The

fuse should be rated at 3 amps and ASTA

approved to BS1362.

However if the plug is unsuitable, it should be

removed from the supply cord and an

appropriate plug fitted as detailed below:-

As the colours of the wires in the mains lead of

this appliance may not correspond with the

coloured markings identifying the terminals in

your plug, proceed as follows:-

The wire which is coloured Blue must be

connected to the terminal which is marked with

the letter N or coloured Black.

The wire which is coloured Brown must be

connected to the terminal which is marked with

the letter L or coloured Red.

NB. Neither wire should be connected to the

terminal in your plug which is marked with the

letter E or by the Earth symbol or coloured

Green or Green and Yellow. If in doubt consult a

qualified electrician.

If any other plug is used, a 3 amp fuse must be

fitted either in the plug or adaptor or at the

distribution board.

32

PLEASE READ AND SAVE THESE

INSTRUCTIONS

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic safety

precautions should always be taken including

the following:-

• Use the fan only for purposes described in

the instruction manual.

• To protect against electrical shock, do not

immerse the fan, plug or cord in water or

spray with liquids.

• Close supervision is necessary when any

appliance is used by or near children.

• Unplug from the electrical outlet when not in

use, when moving the fan from one location

to another, before putting on or taking off

parts and before cleaning.

• Avoid contact with any moving parts.

• Do not operate in the presence of explosive

and/or flammable fumes.

• Do not place the fan or any parts near an

open flame, cooking or other heating

appliance.

• Do not operate any appliance with a damaged

cord, plug, after the appliance malfunctions,

or has been dropped/damaged in any

manner.

• The use of attachments not recommended or

sold by the appliance manufacturer may

cause hazards.

• Do not use outdoors.

• Do not let the cord hang over the edge of a

table or counter, or come into contact with hot

surfaces.

• To disconnect from the electrical supply, grip

the plug and pull from the wall outlet. DO

NOT pull on the cord.

• Always use on a dry, level surface.

• Do not operate without the fan grills properly

in place.

• This product is intended for household use

ONLY and not for commercial or industrial

applications.

MISSING A PART FOR YOUR FAN?

Please call 0800 052 3615 for assistance.

ASSEMBLY INSTRUCTIONS (See Fig 1.)

Base/Pole assembly

You will need the base cover (O), round

weighted insert (P), pole (K,M), pole ring (N)

washer (S) and L-shaped locking lever (Q).

1. Slide the bottom end of the pole through the

pole ring.

2. Turn the base cover upside down and place

the round weighted insert into the base cover.

3. Insert the threaded end of the L-shaped

locking lever into the hole of the washer, round

weighted insert and through the base cover.

4. Whilst holding the base cover and round

weighted insert with one hand, connect the

pole to the base, sliding the L-shaped locking

lever into the bottom of the pole with you other.

5. Turn the L-shaped locking lever clockwise to

securely attach the pole to the base.

6. Set the base on the floor, weight side down.

Push the pole ring down until it sits directly on

the base.

Fan head assembly

You are now ready to assemble the fan head

1. Unscrew rear grill mounting nut (D) before

positioning the rear grill (F) over the motor

shaft (G) making certain that the notches at

the top and bottom of the rear grill, fit over the

prongs on the motor housing (H).

2. Secure the rear grill in its place using the rear

grill mounting nut (D). Turn this nut clockwise

and tighten firmly.

3. Slide the fan blade (B) with the hollowed

interior of the blade facing toward the rear

grill, firmly onto the motor shaft. The top of the

motor shaft should lie even with the centre of

the fan blade.

4. Now use the securing screw (C) (already

attached to the Fan Blade) to lock the blade

into place. Tighten the screw into the side hole

of the fan blade, against the motor shaft, until

both the blade and screw are secure.

5. Centre the front grill (A) by aligning the Bionaire®

logo on the logo plate so that it is horizontal

and parallel with the floor. Then, holding the

front grill against the rear grill, push the black

grill ring (E) into place at the top and bottom of

the fan. (Push directly on the black grill ring,

not on the grills themselves). Finish securing

the grill ring in the same manner until both

grills are joined underneath the black ring.

Final assembly

1. Slide the inner pole extension (K) up from the

outer pole (M). Insert the pole locking knob (L)

into the hole on the outer pole, to securely

hold this position.

2. Place the fan head assembly into this extension

pole, inserting the neck of the fan into the pole

opening. Turn the fan head's neck until the

head is securely locked into place.

3. Add the tilt adjustment knob (J) to the hole in

the fan head's neck. Tighten when the fan head

is in your desired position.

U.K. and IRELAND

BASF1314/1714

Fig. 1

A

B

I

C

R

DE F G H

J

K

L

M

N

O

P

Q

S

BASF1314/1714I05M1 visual.qxd 2/25/06 10:25 Page 4

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Bionaire BASF1314 Ventilador. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Bionaire. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Bionaire BASF1314 Ventilador en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Bionaire Ventiladores
Más manuales de Ventiladores

Preguntas frecuentes sobre Bionaire BASF1314 Ventilador

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Bionaire BT14 Ventilador

Manual de uso

Bionaire BAOF25M Ventilador

Manual de uso

Bionaire BASF1415 Ventilador

Manual de uso

Bionaire BT18 Ventilador

Manual de uso

Bionaire BAC14 Ventilador

Manual de uso

Bionaire BASF 1016 G Ventilador

Manual de uso

Bionaire BASF40LM Ventilador

Manual de uso

Bionaire BAOF30W Ventilador

Categorias relacionadas