Manual de uso Black and Decker GTC18504PC-QW Tijeras cortasetos

Manual de uso

7

ENGLISH

(Original instructions)

#

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on the

rating plate. Never attempt to replace the charger

unit with a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Trigger switch

2. Lock off button

3. Switch handle

4. POWERCOMMAND button

5. Blade guard

6. Dual switch bail handle

7. Blade

8. Battery

9. Charger

Assembly

Warning! Before assembly, remove the battery from the tool

t the blade sheath over the blades.

Warning! Before assembly, make sure that the tool is

switched off and unplugged and that the blade sheath is tted

over the blades.

Warning! Never use the tool without the guard.

Charging procedure

Black+decker chargers are designed to charge Black+decker

battery packs.

u Plug the charger into an appropriate outlet before inserting

the battery pack.

u Insert the battery pack into the charger as shown in gure

A.

u The green LED will ash indicating that the battery is be-

ing charged.

u The completion of charge is indicated by the green LED

remaining on continuously. The pack is fully charged and

may be used at this time or left on the charger.

Note: Recharge discharged batteries as soon as possible

after use or battery life may be greatly diminished. For longest

battery life, do not discharge batteries fully. It is recommended

that the batteries be recharged after each use.

Leaving the battery in the charger

The charger and battery pack can be left connected with the

LED glowing indenitely. The charger will keep the battery

pack fresh and fully charged.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65°F and 75°F (18°- 24°C). DO NOT charge the

battery pack in an air temperature below +40°F (+4.5°C),

or above +105°F (+40.5°C). This is important and will

prevent serious damage to the battery pack.

u The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack

in a warm environment such as in a metal shed, or an

uninsulated trailer.

u If the battery pack does not charge properly:

u Check current at receptacle by plugging in a lamp or

other appliance.

u Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F

- 75°F (18°- 24°C).

u If charging problems persist, take the tool, battery pack

and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, steel wool, aluminium foil, or any buildup

of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger

before attempting to clean.

u Do not freeze or immerse charger in water or any other

liquid.

Warning! Do not allow any liquid to get inside charger. Never

attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, return to a

service center for recycling.

Installing and removing the battery pack from the

tool

Warning! Make certain the lock-off button is engaged to

prevent switch actuation before removing or installing battery.

To install battery pack

u Insert battery (8) into tool until an audible click is heard

(Figure. B)

u Ensure battery pack is fully seated and fully latched into

position.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Black and Decker GTC18504PC-QW Tijeras cortasetos. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Black and Decker. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Black and Decker GTC18504PC-QW Tijeras cortasetos en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Black and Decker Tijeras cortasetos
Más manuales de Tijeras cortasetos

Preguntas frecuentes sobre Black and Decker GTC18504PC-QW Tijeras cortasetos

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Black and Decker GTC36552PC Tijeras cortasetos

Manual de uso

Black and Decker GTC1845L20-QW Tijeras cortasetos

Manual de uso

Black and Decker GTC2451 Tijeras cortasetos

Manual de uso

Black and Decker GT535 Tijeras cortasetos

Manual de uso

Black and Decker GT220P Tijeras cortasetos

Manual de uso

Black and Decker GT340JP01 Tijeras cortasetos

Manual de uso

Black and Decker GT460SXC Tijeras cortasetos

Manual de uso

Black and Decker GT250 Tijeras cortasetos

Categorias relacionadas