Manual de uso Black and Decker KA86 Lijadora de banda

Manual de uso

5

ENGLISH

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will make sure that the safety of the power tool is

maintained.

Additional power tool safety warnings

 Hold the power tool by insulated gripping surfaces,

because the sanding belt / sanding base may

contact its own cord. Cutting a "live" wire may make

exposed metal parts of the power tool "live" could give

the operator an electric shock.

 Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body leaves it unstable

and may lead to loss of control.

 Warning! Contact with or inhalation of dust arising from

sanding applications may endanger the health of the

operator and possible bystanders. Wear a dust mask

specifically designed for protection against dust and

fumes and ensure that persons within or entering the

work area are also protected.

 Thoroughly remove all dust after sanding.

 Take special care when sanding paint which is possibly

lead based or when sanding some woods and metal which

may produce toxic dust:

 Do not let children or pregnant women enter the work area.

 Do not eat, drink or smoke in the work area.

 Dispose of dust particles and any other debris safely.

The intended use is described in this instruction manual. The use

of any accessory or attachment or performance of any

operation with this tool other than those recommended in

this instruction manual may present a risk of personal injury

and/or damage to property.

Safety of others

 This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a

person responsible for the their safety.

 Children should be supervised to ensure that they do

not play with the appliance.

Vibration

The declared vibration emission values stated in the

technical data and the declaration of conformity have been

measured in accordance with a standard test method

provided by EN 60745 and may be used for comparing one

tool with another. The declared vibration emission value may

also be used in a preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons

regularly using power tools in employment, an estimation of

vibration exposure should consider, the actual conditions of

use and the way the tool is used, including taking account of

all parts of the operating cycle such as the times when the

tool is switched off and when it is running idle in addition to

the trigger time.

Labels on tools

Electrical safety

This tool is double insulated; therefore no earth

wire is required. Always check that the power

supply corresponds to the voltage on the rating

plate.

 If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised Black & Decker Service

Centre in order to avoid a hazard.

Warning! Additional safety warnings for sanders.

!

Warning! To reduce the risk of injury, the user must

read the instruction manual.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Black and Decker KA86 Lijadora de banda. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Black and Decker. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Black and Decker KA86 Lijadora de banda en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Black and Decker Lijadoras de banda
Más manuales de Lijadoras de banda

Preguntas frecuentes sobre Black and Decker KA86 Lijadora de banda

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Black and Decker XTA900E Lijadora de banda

Manual de uso

Black and Decker KA75 Lijadora de banda

Manual de uso

Black and Decker KA85 Lijadora de banda

Manual de uso

Black and Decker BR318 Lijadora de banda

Manual de uso

Black and Decker KA83E Lijadora de banda

Manual de uso

Black and Decker KA89E Lijadora de banda

Manual de uso

Black and Decker KA900E Lijadora de banda

Manual de uso

Black and Decker XTA80EK Lijadora de banda

Categorias relacionadas