Manual de uso Black and Decker KR600CRE Taladradora de percusión

Manual de uso

4

ENGLISH

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Side handle

4. Depth stop

5. Chuck

6. Drilling mode selector

7. Forward/reverse switch

8. Variable speed control knob

9. Spindle lock button

Assembly

Warning! Make sure that the tool is switched off and unplugged.

Fitting the side handle and depth stop (fig. A)

◆ Turn the grip (10) counterclockwise until you can slide the

side handle (3) onto the front of the tool as shown.

◆ Rotate the side handle into the desired position.

◆ Insert the depth stop (4) into the mounting hole as shown.

◆ Set the depth stop to the desired position. The maximum

drilling depth is equal to the distance between the tip of

the drill bit and the front end of the depth stop.

◆ Tighten the side handle by turning the grip clockwise.

Fitting a drill bit or screwdriver bit

Keyless chuck with spindle lock (fig. B)

◆ Keep the spindle lock button (9) depressed and open the

chuck.

◆ Insert the bit shaft (11) into the chuck and firmly tighten

the chuck.

Keyless chuck (fig. C)

◆ Open the chuck by turning the front part (12) with one

hand while holding the rear part (13) with the other.

◆ Insert the bit shaft (11) into the chuck and firmly tighten

the chuck.

Keyed chuck (fig. D)

◆ Open the chuck by turning the sleeve (14).

◆ Insert the bit shaft (11) into the chuck.

◆ Insert the chuck key (15) into each hole (16) in the side of

the chuck and turn until tight.

Removing and refitting the chuck (fig. E)

◆ Open the chuck as far as possible.

◆ Remove the chuck retaining screw by turning it clockwise

using a screwdriver.

◆ Tighten an Allen key (17) into the chuck and strike it with

a hammer as shown.

◆ Remove the Allen key.

◆ Remove the chuck by turning it counterclockwise.

◆ To refit the chuck, screw it onto the spindle and secure it

with the chuck retaining screw.

Use

Warning! Before drilling into walls, floors or ceilings,

check for the location of wiring and pipes.

Selecting the direction of rotation

◆ For drilling and for tightening screws, slide the forward/

reverse switch (7) forward.

◆ For loosening screws or removing a jammed drill bit, slide

the forward/reverse switch (7) backward.

Warning! Never change the direction of rotation while the

motor is running.

Selecting the drilling mode

◆ For drilling in masonry, set the drilling mode selector (6) to

the position.

◆ For drilling in other materials and for screwdriving, set the

drilling mode selector (6) to the position.

Switching on and off

◆ To switch the tool on, press the variable speed switch (1).

The tool speed depends on how far you press the switch.

If the tool has a variable speed control knob (8), set it to

the required speed range. As a general rule, use low

speeds for large diameter drill bits and high speeds for

smaller diameter drill bits.

◆ For continuous operation, press the lock-on button (2) and

release the variable speed switch. This option is available

only at full speed.

◆ To switch the tool off, release the variable speed switch.

To switch the tool off when in continuous operation, press

the variable speed switch once more and release it.

Accessories

The performance of your tool depends on the accessory used.

Black & Decker and Piranha accessories are engineered to high

quality standards and designed to enhance the performance of

your tool. By using these accessories you will get the very best

from your tool.

Maintenance

Your tool has been designed to operate over a long period of

time with a minimum of maintenance. Continuous satisfactory

operation depends upon proper tool care and regular cleaning.

Protecting the environment

Black & Decker provides a facility for recycling

Black & Decker products once they have reached the

end of their working life.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Black and Decker KR600CRE Taladradora de percusión. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Black and Decker. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Black and Decker KR600CRE Taladradora de percusión en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Black and Decker Taladradoras de percusión
Más manuales de Taladradoras de percusión

Preguntas frecuentes sobre Black and Decker KR600CRE Taladradora de percusión

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Black and Decker KR8542K Taladradora de percusión

Manual de uso

Black and Decker KR650CRE Taladradora de percusión

Manual de uso

Black and Decker KR700CRE Taladradora de percusión

Manual de uso

Black and Decker KR655 Taladradora de percusión

Manual de uso

Black and Decker KD356 Taladradora de percusión

Manual de uso

Black and Decker KR910K Taladradora de percusión

Manual de uso

Black and Decker KR550CRE Taladradora de percusión

Manual de uso

Black and Decker KR510XC Taladradora de percusión

Categorias relacionadas