Manual de uso Black and Decker KX1693 Decapador por aire caliente

Manual de uso

5

ENGLISH

d. Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5. Service

a. Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will make sure that the safety of the power tool is

maintained.

Additional safety warnings

Warning! Do not use outdoors, indoor use only.

Warning! This appliance is not intended for use by persons

(including children) with reduced physical, sensory, or

mental capabilities, or lack of experience or knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for

their safety.

Warning! Children should be supervised to ensure that they

do not play with the appliance.

Warning! This appliance must be placed on its stand when

not in use.

Warning! A fire may result if the appliance is not used with

care, therefore be careful when using the appliance in places

where there are combustible materials;

X Do not apply heat to the same place for a long time;

X Do not use in presence of an explosive atmosphere;

X Be aware that heat may be conducted to combustible

materials that are out of sight;

X Place the appliance on its stand after use and allow it to

cool down before storage.

X Do not leave the appliance unattended when it is

switched on.

X Do not obstruct either the air intake slots or the nozzle

outlet as this may cause excessive heat build up

resulting in damage to the appliance.

X Do not direct the hot air flow at other people or animals.

X Do not touch the nozzle as it becomes very hot during

use and remains hot for up to 30 minutes after use.

X Do not place the nozzle against any object during or

immediately after use.

X Do not poke anything down the nozzle as it could give

you an electric shock.

X Do not look down the nozzle while the appliance is

switched on.

X Do not use the appliance as a hairdryer! The air

temperature is far higher than a hairdryer.

X Ensure adequate ventilation during use as toxic fumes

may be produced.

X Do not use the appliance in a damp atmosphere.

X When stripping paint, ensure that the work area is

enclosed. Wear a dust mask specifically designed for

protection against lead paint dust and fumes and ensure

that persons within or entering the work area are also

protected.

X Do not burn paint, as it could cause a fire hazard.

X Do not allow paint to adhere to the nozzle as it could

ignite after some time.

X Switch off the appliance and allow it to cool before fitting

any accessory.

Stripping lead-based paint

X Extreme care should be taken when stripping paint. The

peelings, residue and vapours of paint may contain

lead, which is poisonous. Any pre-1960 building may in

the past have been painted with paint containing lead.

This paint may be covered with additional layers of

paint. Once deposited on surfaces, hand to mouth

contact can result in the ingestion of lead.

X Exposures to even low levels of lead can cause

irreversible brain and nervous system damage. The

greatest danger of lead poisoning is to children and

pregnant women.

X Before starting work, it is important to determine

whether the paint to be stripped contains lead. This can

be done using a test kit or by a professional decorator.

Do not smoke, eat or drink in a work area that could or

may be contaminated by lead. Lead based paints

should only be removed by a professional and should

not be removed using a heat gun.

Warning! Additional safety instructions for heat

guns.

!

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Black and Decker KX1693 Decapador por aire caliente. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Black and Decker. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Black and Decker KX1693 Decapador por aire caliente en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Black and Decker Decapadores por aire caliente
Más manuales de Decapadores por aire caliente

Preguntas frecuentes sobre Black and Decker KX1693 Decapador por aire caliente

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Black and Decker KX2000K Decapador por aire caliente

Manual de uso

Black and Decker KX1683 Decapador por aire caliente

Manual de uso

Black and Decker KX1692 Decapador por aire caliente

Manual de uso

Black and Decker CD700 Decapador por aire caliente

Manual de uso

Black and Decker KX1682 Decapador por aire caliente

Manual de uso

Black and Decker HG2000K Decapador por aire caliente

Manual de uso

Black and Decker KX2200 Decapador por aire caliente

Manual de uso

Black and Decker KX2001 Decapador por aire caliente

Categorias relacionadas