Manual de uso Black and Decker NHT518L Tijeras cortasetos

Manual de uso

5. Use of an attachment not recommended or sold by Black & Decker may result in a risk

of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when

disconnecting charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire, electric shock or electrocution.

a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round

jacketed extension cords should be used, and we recommend that they be listed by

Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord

must be suitable for outdoor use. Any cord marked for outdoor use can also be

used for indoor work. The letters "W" or "WA" on the cord jacket indicate that the

cord is suitable for outdoor use.

b. An extension cord must have adequate wire size (AWG or American Wire Gauge)

for safety, and to prevent loss of power and overheating. The smaller the gauge

number of the wire, the greater the capacity of the cable; that is, 16 gauge has

more capacity than 18 gauge. When using more than one extension to make up the

total length, be sure each extension contains at least the minimum wire size.

C H A RT FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS

N A M E P L ATE RATING AMPS – 0 – 10.0

Total Extension Cord Length (ft) 2 5 5 0 7 5 1 0 0 125 150

Wire Gauge 1 8 1 8 1 6 1 6 14 14

9. Use only the supplied charger when charging your unit. The use of any other charger

could damage the battery or create a hazardous condition.

10. Use only one charger when charging.

11. Do not attempt to open the charger or the unit. There are no customer serviceable

parts inside. Return to any authorized Black & Decker service center.

12. DO NOT incinerate battery packs even if they are severely damaged or completely

worn out.

13. Do not incinerate the batteries. They can explode in a fire. A small leakage of liquid

from the battery cells may occur under extreme usage, charging or temperature

conditions. This does not indicate a failure. However, if the outer seal is broken and this

leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of

10 minutes and seek immediate medical attention.

MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide.

SAVE THESE INSTRUCTIONS

IMPORTANT CHARGING SAFETY

INSTRUCTIONS

CHARGING THE POWER PACK

THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE

FA C T O R Y. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF

THE SAFETY INSTRUCTIONS.

The charger is designed to use standard household 120 volt 60 Hz power.

1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet. NOTE: Do not charge

by means of an engine generator or DC power source. Use only 120V AC.

2. Slide the charger onto the power pack as shown in Figure 1 & 2 and let the power pack

charge initially for 9 hours. After the initial charge, under normal usage, your power pack

should be fully charged in 3 to 6 hours.

3. Unplug charger, and remove the power pack. Place the power pack in the unit and be

certain that it is inserted fully into the battery cavity until it “clicks” into place.

(Figure 4)

NOTE: To remove the power pack from the unit, press down on the release button on

the back of the pack (Figure 3) and slide out.

IMPORTANT CHARGING NOTES

1. After normal usage, your power pack should be fully charged in 3 to 9 hours. If the

power pack is run-down completely, it may take up to 9 hours to become fully charged.

Your power pack was sent from the factory in an uncharged condition. Before

attempting to use it, it must be charged for at least 9 hours.

2. DO NOT charge the power pack in an air temperature below +40°F(+4.5°C), or above

+105°F (+40.5°C). This is important and will prevent serious damage to the power pack.

Longest life and best performance can be obtained if power pack is charged when air

temperature is about 75°F (2 4 ° C ).

3. While charging, the charger may hum and become warm to touch. This is a normal

condition and does not indicate a problem.

4. If the power pack does not charge properly—(1) Check current at receptacle by plugging

in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights. (3) Move charger and power pack to

a surrounding air temperature of 40°F (+4.5°C) to 105°F ( + 4 0 . 5 ° C ). (4) If the receptacle

and temperature are OK, and you do not get proper charging, take or send the power

pack and charger to your local Black & Decker service center. See Tools Electric in

yellow pages.

5. The power pack should be recharged when it fails to produce sufficient power on jobs

which were easily done previously. DO NOT CONTINUE using unit with its power pack

in a depleted condition.

6. The power pack will reach optimum performance after being cycled 5 times during normal

usage. There is no need to run the batteries down completely before recharging. Normal

usage is the best method of discharging and recharging the power pack.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the red light glowing indefinitely. T h e

charger will keep the battery pack fresh and fully charged.

N O T E : A battery pack will slowly lose its charge when kept out of the charger. If the battery

pack has not been kept on maintenance charge, it may need to be recharged before use. A

battery pack may also slowly lose its charge if left in a charger that is not plugged into an

appropriate AC source.

S W I T C H

To turn the unit “ON”, slide the lock off button, shown in Figure 5, forward and, squeeze the

trigger switch. Once the unit is running, you may release the lock off button. In order to keep

the unit running you must continue to squeeze the trigger. To turn the unit “OFF”, simply

release the trigger.

TRIMMING INSTRUCTIONS

1. WORKING POSITION – Maintain proper footing and balance and do not overreach.

Wear safety goggles, non-skid footwear and rubber gloves when trimming. Hold the

unit firmly in both hands and turn the unit ON. Always hold the trimmer, as shown in the

illustrations in this manual, with one hand on the switch handle and one hand on the bail

handle. (Figure 6) Never hold the unit by the blade guard.

2. TRIMMING NEW GROWTH – (Figure 8) A wide, sweeping motion, feeding the blade

teeth through the twigs is most effective. A slight downward tilt of the blade, in the direc-

tion of motion gives the best cutting.

CAUTION: Do not cut stems greater than 7/16” (12mm). Use the

trimmer only for cutting normal shrubbery around houses and buildings.

3. LEVEL HEDGES (Figure 7) – To obtain exceptionally level hedges a piece of string can

be stretched along the length of the hedge as a guide.

4. SIDE TRIMMING HEDGES (Figure 9) – Hold the trimmer as shown and begin at the bot-

tom and sweep up.

WARNING: TO GUARD A G A I N S T I N J U R Y, OBSERVE THE FOLLOWING:

• READ INSTRUCTION MANUAL BEFORE USING.

• SAVE INSTRUCTION MANUAL.

• KEEP HANDS AWAY FROM BLADES.

• KEEP HANDS ON HANDLES. DON’T OVERREACH.

• CAUTION – BLADE MAY COAST AFTER TURN OFF.

• DO NOT USE UNDER WET CONDITIONS.

MAINTENANCE

A vinyl sheath is supplied with your trimmer. Slip the hedge trimmer into it, as shown in

Figure 10. The cutting blades are made from high quality, hardened steel and with normal

usage, they will not require resharpening. H o w e v e r, if you accidentally hit a wire fence,

stones, glass or other hard objects, you may put a nick in the blade. There is no need to

remove this nick as long as it does not interfere with the movement of the blade. If it does

interfere, remove the battery and use a fine toothed file or sharpening stone to remove the

n i c k .

If you drop the trimmer, carefully inspect it for damage. If the blade is bent, housing cracked,

or handles broken or if you see any other condition that may affect the trimmer’s operation

contact your local Black & Decker Service Center for repairs before putting it back into use.

Fertilizers and other garden chemicals contain agents which greatly accelerate the corrosion

of metals. Do not store the unit on or adjacent to fertilizers or chemicals.

With the battery removed, use only mild soap and a damp cloth to clean the unit. Never let

any liquid get inside the unit; never immerse any part of the unit into a liquid.

Prevent the blades from rusting by applying a film of light machine oil after cleaning.

WARNING: DO NOT use the hedge trimmer with any type of accessory or

attachment. Such usage might be hazardous.

THE RBRC™ SEAL

The RBRC™ (Rechargeable Battery Recycling Corporation)

Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to

recycle the battery (or battery pack) at the end of its useful life have already

been paid by Black & Decker. In some areas, it is illegal to place spent

nickel-cadmium batteries in the trash or municipal solid waste stream and the RBRC

program provides an environmentally conscious alternative.

RBRC in cooperation with Black & Decker and other battery users, has established

programs in the United States and Canada to facilitate the collection of spent nickel-

cadmium batteries. Help protect our environment and conserve natural resources by

returning the spent nickel-cadmium battery to an authorized Black & Decker service center

or to your local retailer for recycling. You may also contact your local recycling center for

information on where to drop off the spent battery, or call 1 - 8 0 0 - 5 4 4 - 6 9 8 6 .

I M P O R TA N T

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should

be performed by authorized service centers or other qualified service organizations, always

using identical replacement parts.

SERVICE INFORMATION

All Black & Decker Service Centers are staffed with trained personnel to provide customers

with efficient and reliable power tool service. Whether you need technical advice, repair, or

genuine factory replacement parts, contact the Black & Decker location nearest you. To find

your local service location, refer to the yellow page directory under "Tools—Electric" or call:

1-800-544-6986 or visit www. b l a c k a n d d e c k e r. c o m

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in

material or workmanship. The defective product will be replaced or repaired at no charge in

either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should be

made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after

the sale). Proof of purchase may be required. Please check with the retailer for their specific

return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may be

required.Black & Decker owned and authorized Service Centers are listed under

" Tools-Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state or province to province. Should

you have any questions, contact the manager of your nearest Black & Decker Service

C e n t e r. This product is not intended for commercial use.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are

missing, call 1-800-544-6986 for a free replacement.

See ‘Tools-Electric’

– Yellow Pages –

for Service & Sales

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

TROUBLESHOOTING

P r o b l e m Possible Cause Possible Solution

• Slow running, noisy • Dry, corroded blades. • Lubricate blades.

or hot blades. • Blades or blade support bent. • Straighten blade or blade

s u p p o r t .

• Bent or damaged teeth. • Straighten teeth.

• Loose blade bolts. • Tighten blade bolts.

• Unit does not run. • Battery not making contact. • Check battery is full inserted.

• Lock off not fully operated. • Check that lock off is fully

forward prior to moving main

t r i g g e r.

• Battery not installed properly. • Check battery installation.

• Battery not charged. • Check battery charging

r e q u i r e m e n t s .

• Battery will not charge. • Battery not inserted into charger. • Insert battery into charger

until red LED appears.

• Charger not plugged in. • Plug charger into a working

outlet. Refer to “Important

Charging Notes” for more

d e t a i l s .

• Check current at receptacle

by plugging in a lamp or other

a p p l i a n c e .

• Check to see if receptacle is

connected to a light switch

which turns power off when

you turn out the lights.

• Surrounding air temperature • Move charger and tool to a

too hot or too cold. surrounding air temperature

of above 40 degree F(4 , 5 °C)

or below 105 degree F

(+ 4 0 , 5°C ).

For assistance with your product, visit our website www.blackanddecker.com for the loca-

tion of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Black and Decker NHT518L Tijeras cortasetos. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Black and Decker. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Black and Decker NHT518L Tijeras cortasetos en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Black and Decker Tijeras cortasetos
Más manuales de Tijeras cortasetos

Preguntas frecuentes sobre Black and Decker NHT518L Tijeras cortasetos

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Black and Decker GT220 Tijeras cortasetos

Manual de uso

Black and Decker GT250 Tijeras cortasetos

Manual de uso

Black and Decker GTC5455PCB Tijeras cortasetos

Manual de uso

Black and Decker GT6026 Tijeras cortasetos

Manual de uso

Black and Decker GT5560 Tijeras cortasetos

Manual de uso

Black and Decker GT524 Tijeras cortasetos

Manual de uso

Black and Decker GT670 Tijeras cortasetos

Manual de uso

Black and Decker GL602 Tijeras cortasetos

Categorias relacionadas