Manual de uso Bosch GSR 12V-15 FC Atornillador taladrador

Manual de uso

10 | English

battery (5) into the handle until you feel it engage and it is

flush with the handle.

Setting the rotational direction (see figureH)

The rotational direction switch (6) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (7) is being pressed.

Right rotation: To drill and to drive in screws, press the ro-

tational direction switch (6) through to the left stop.

Left Rotation: To loosen and unscrew screws and nuts,

press the rotational direction switch (6) through to the right

stop.

Preselecting the Torque

The torque presetting ring (2) can be used to preselect the

required torque in 15 stages. When the correct setting is

used, the application tool will be stopped when the screw is

driven flush into the material or once the set torque has been

reached. In position the overload clutch is deactivated,

e.g. for drilling.

When unscrewing screws, it may be advisable to select a

higher setting or the symbol.

Mechanical gear selection

u Only operate the gear selector (3) when the power

tool is not in use.

You can preselect two speed ranges with the gear selector

(3).

Gear I:

Low speed range; for screwdriving or working with a large

drilling diameter.

Gear II:

High speed range; for working with a small drilling diameter.

u Always push the gear selector switch as far as it will

go. Otherwise, the power tool may become damaged.

Switching on/off

To start the power tool, press and hold the on/off switch

(7).

The worklight (9) lights up when the on/off switch (7) is

lightly or fully pressed, allowing the work area to be illumin-

ated in poor lighting conditions.

The worklight (9) will remain lit for approximately ten

seconds after the on/off switch (7) has been released.

Adjusting the Speed

You can adjust the speed of the power tool when it is on by

pressing in the on/off switch (7) to varying extents.

A light pressure on the on/off switch (7) results in a low rota-

tional speed. Increased pressure on the switch causes an in-

crease in speed.

Fully automatic spindle lock (Auto-Lock)

The drill spindle, and therefore the holder (1), are locked

when the on/off switch (7) is not pressed.

This enables screws to be screwed in even when the battery

is empty and allows the power tool to be used as a screw-

driver.

Temperature-dependent overload protection

In normal conditions of use, the power tool cannot be over-

loaded. If the power tool is overloaded or not kept within the

permitted operating temperature range, the power output is

reduced or the power tool is switched off. The power tool

will not run at full power output again until the permitted op-

erating temperature has been reached.

Battery charge indicator

When the on/off switch (7) is pressed in halfway or com-

pletely, the battery charge-control indicator (8) indicates

the charge condition of the battery for several seconds. The

indicator consists of three green LEDs.

LEDs Capacity

3× continuous green light ≥66%

2× continuous green light ≥33%

1× continuous green light <33%

1× flashing green light Reserve

Practical advice

u Only apply the power tool to the screw when the tool

is switched off. Rotating application tools can slip off.

After working at a low speed for an extended period, you

should operate the power tool at the maximum speed for ap-

proximately three minutes without load to cool it down.

When drilling into metal, only use sharpened HSS drills (HSS

= high-speed steel) which are in perfect condition. The

Bosch accessory range guarantees appropriate quality.

Before screwing larger, longer screws into hard materials, it

is advisable to pre-drill a pilot hole with the core diameter of

the thread to approx. 2/3 of the screw length.

Maintenance and Service

Maintenance and Cleaning

u Remove the battery from the power tool before carry-

ing out work on the power tool (e.g. maintenance,

changing tool, etc.). The battery should also be re-

moved for transport and storage. There is risk of injury

from unintentionally pressing the on/off switch.

u To ensure safe and efficient operation, always keep

the power tool and the ventilation slots clean.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-

ing maintenance and repair of your product as well as spare

parts. You can find explosion drawings and information on

spare parts at: www.bosch-pt.com

The Bosch product use advice team will be happy to help you

with any questions about our products and their accessor-

ies.

In all correspondence and spare parts orders, please always

include the 10‑digit article number given on the nameplate

of the product.

1 609 92A 53J | (03.07.2020) Bosch Power Tools

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Bosch GSR 12V-15 FC Atornillador taladrador. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Bosch. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Bosch GSR 12V-15 FC Atornillador taladrador en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Bosch Atornilladores taladrador
Más manuales de Atornilladores taladrador

Preguntas frecuentes sobre Bosch GSR 12V-15 FC Atornillador taladrador

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Bosch GSR 18V-28 Atornillador taladrador

Manual de uso

Bosch GSR 14,4 V-LI Professional Atornillador taladrador

Manual de uso

Bosch PSB Universal LI-2 Atornillador taladrador

Manual de uso

Bosch GSR 12V-35 HX Atornillador taladrador

Manual de uso

Bosch PSR 180 LI-8 Atornillador taladrador

Manual de uso

Bosch GSR 18VE-EC Atornillador taladrador

Manual de uso

Bosch PSR 14.4 LI Atornillador taladrador

Manual de uso

Bosch GSB 10.8-2-LI Professional Atornillador taladrador

Categorias relacionadas