Manual de uso DeWalt DW318G Sierra de calar

¿Necesita un manual para su DeWalt DW318G Sierra de calar? A continuación puedes ver y descargar el manual en PDF gratis en español. Este producto actualmente tiene 4 preguntas frecuentes, 0 comentarios y tiene 0 votos. Si este no es el manual que desea, , contáctenos.

¿Su producto tiene algún defecto y el manual no ofrece ninguna solución? Vaya a Repair Café para solicitar un servicio de reparación gratuito.

Manual de uso

Loading…

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY D
EWALT TOOL,
CALL US TOLL FREE AT:
1-800-4-DEWALT (1-800-433-9258)
Important Safety Instructions
WARNING: When using electric tools, basic safety precautions should always be fol-
lowed to reduce risk of fire, electric shock, and personal injury, including the following:
READ ALL INSTRUCTIONS
Double Insulation(DW313, DW318, DW318-220)
Double insulated tools are constructed throughout with two separate layers of electrical insu-
lation or one double thickness of insulation between you and the tool’s electrical system.
Tools built with this insulation system are not intended to be grounded. As a result, your tool is
equipped with a two prong plug which permits you to use extension cords without concern for
maintaining a ground connection.
NOTE: Double insulation does not take the place of normal safety precautions when operat-
ing this tool. The insulation system is for added protection against injury resulting from a pos-
sible electrical insulation failure within the tool.
CAUTION: When servicing all tools, USE IDENTICAL REPLACEMENT PARTS. Repair or
replace damaged cords.
Polarized Plugs (DW313, DW318)
Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk
of electric shock. When provided, this plug will fit in the polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified elec-
trician to install the proper outlet. Do not change the plug in any way.
Grounding Instructions (DW318G)
This tool should be grounded while in use to protect the operator from electric shock. The tool
is equipped with a 3-conductor cord and 3-prong grounding type plug to fit the proper ground-
ing type receptacle. The green (or green and yellow) conductor in the cord is the grounding
wire. Never connect the green (or green and yellow) wire to a live terminal. If your unit is intend-
ed for use on less than 150 V, it has a plug that looks like that shown in sketch A. If it is for use
on 150 to 250 V, it has a plug that looks like that shown in sketch D. An adapter, sketches B
and C, is available for connecting sketch A type plugs to 2-prong receptacles. The green-col-
ored rigid ear, lug, or the like, extending from the adapter must be connected to a permanent
ground, such as a properly grounded outlet box. No adapter is available for a plug as shown
in sketch D. ADAPTER SHOWN IN FIGURES B and C IS NOT FOR USE IN CANADA.
Safety Instructions For All Tools
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
CONSIDER WORK AREA ENVIRONMENT. Don’t expose power tools to rain. Don’t use
power tools in damp or wet locations. Keep work area well lit. Do not use tool in presence
of flammable liquids or gases.
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For
example; pipes, radiators, ranges, and refrigerator enclosures.
KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors
should be kept away from work area.
STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked-
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
DW313,DW318,DW318G, DW318-220
Variable Speed Orbital Jig Saws
Scies sauteuses excentriques à régulateur de vitesse
Sierras caladoras con velocidad variable orbital
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y
PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUC-
TIVO ANTES DE USAR EL PRODUCTO.
Questions? See us on the World Wide Web at www.dewalt.com
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
(XXX-XX) Form No.384014-01 DW313 Copyright © 2003
The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air
intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the
surface of the tool.
up place — out of reach of children.
DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was intend-
ed.
USE RIGHT TOOL. Don’t force small tool or attachment to do the job of a heavy-duty tool.
Don’t use tool for purpose not intended.
DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving
parts. Rubber gloves and non-skid footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
Air vents often cover moving parts and
should also be avoided.
USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty.
DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle.
Keep cord from heat, oil, and sharp edges.
SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your hand and it
frees both hands to operate tool.
DON’T OVERREACH. Keep proper footing and balance at all times.
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer perform-
ance. Follow instructions for lubricating and changing accessories. Inspect tool cords peri-
odically and if damaged, have repaired by authorized service facility. Inspect extension
cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and
grease.
DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and when
changing accessories, such as blades, bits, cutters.
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys
and adjusting wrenches are removed from tool before turning it on.
AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be sure switch
is off when plugging in.
EXTENSION CORDS. Use only 3-wire extension cords that have 3-prong grounding-type
plugs and 3-pole receptacles that accept the tool’s plug. Replace or repair damaged cords.
Make sure your extension cord is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will draw. An undersized cord will
cause a drop in line voltage resulting in loss of power and overheating. The following table
shows the correct size to use depending on cord length and nameplate ampere rating. If in
doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
240V 0-50 51-100 101-200 201-300
Ampere Rating
More Not more AWG
ThanThan
0- 6 18161614
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension
cords intended for use outdoors and so marked.
STAYALERT. Watch what you are doing. Use common sense. Do not operate tool when you
are tired.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is
damaged should be carefully checked to determine that it will operate properly and perform
its intended function. Check for alignment of moving parts, binding of moving parts, breakage
of parts, mounting, and any other conditions that may affect its operation. A guard or other
part that is damaged should be properly repaired or replaced by an authorized service center
unless otherwise indicated elsewhere in this instruction manual. Have defective switches
replaced by authorized service center. Do not use tool if switch does not turn it on and off.
Additional Safety Instructions for Jig Saws
CAUTION: When cutting into walls, floors or wherever live electrical wires may be
encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by
insulated grasping surfaces to prevent electric shock if you cut into a live wire.
KEEP HANDS AWAY from cutting area. Never reach underneath the material for any rea-
son.
KEEP BLADES SHARP. Dull blades may cause the saw to swerve or stall under pressure.
CAUTION: Wear appropriate hearing protection during use. Under some conditions and
duration of use, noise from this product may contribute to hearing loss.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-
struction activities contains chemicals known to cause cancer, birth defects or other reproduc-
tive harm. Some examples of these chemicals are:
lead from lead-based paints,
crystalline silica from bricks and cement and other masonry products, and
arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing and wash exposed areas with soap and
water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorp-
tion of harmful chemicals.
SAVE THESE INSTRUCTIONS
Motor
Your DEWALT tool is powered by a DEWALT-built motor. Be sure your power supply agrees
with the nameplate marking.
Volts 50/60 Hz or “AC only” means your tool must be operated only with alternating current and
never with direct current.
Voltage decrease of more than 10% will cause loss of power and overheating. All D
EWALT
tools are factory tested; if this tool does not operate, check the power supply.
Variable Speed Switch (Fig. 1)
This switch has a button “A”, mounted in the trigger, which can be rotated to vary the blade
strokes-per-minute (S.P.M.).
a. For “Free Hand” speed control (the further the trigger is depressed, the higher the S.P.M.),
rotate the button in the “HI” direction (clockwise) until it stops.
b. To set the trigger switch to produce a selected speed each time the trigger is squeezed,
first rotate the button toward “HI” until it stops. Then fully depress the trigger, press in the
locking button “B”, and release the trigger. The tool will stay “ON”. Now, rotate the button
“A” toward “LO” and you will notice a decrease in speed. Continue rotating the button until
desired speed is obtained. Pull trigger and release to turn the tool “OFF”. At this setting the
saw will run at the selected speed each time the trigger is pulled and the trigger may be
locked “ON” at the selected speed.
Straight Line or Orbital Cutting Action (DW318,
DW318G, DW318-220)
For cutting softer materials your saw features orbital cutting action. Soft materials, like wood
and plastic, permit deep penetration of individual saw teeth. The orbital action thrusts the blade
forward on the cutting stroke and greatly increases cutting speed over conventional jig saws.
Harder materials like metal should be cut using the straight line cutting action or a very low
orbital setting. To select straight line or orbital cutting adjust the lever on the saw as shown in
Figure 2.
Bevel Cutting Adjustment
Bevel cuts may be made at any angle between 0° and 45°. The shoe is adjusted by loosening
the screw on the bottom of the tool (Fig. 3) and rotating the shoe to the desired angle. After
setting the shoe, tighten the screw firmly and use saw in the normal manner.
NOTE: One hand on the saw body and the other on the edge of the saw shoe, well back from
the blade, may be necessary to maintain accurate cutting.
AB CD
GROUNDING PIN
GROUNDED
OUTLET
BOX
GROUNDING
MEANS
GROUNDING PIN
ADAPTER
Descargue el manual en Español (PDF, 0.2 MB)
(Piense en el medioambiente y solo imprima este manual si es de verdad necesario)

Loading…

Puntuación

Dé su opinión de la DeWalt DW318G Sierra de calar calificando el producto. ¿Quiere compartir su experiencia con este producto o hacer una pregunta? Deje un comentario en la parte inferior de la página.
¿Estás satisfecho con elDeWalt DW318G Sierra de calar?
No
Sea el primero en calificar este producto
0 votos

Únase a la conversación sobre este producto

Aquí puedes compartir lo que piensas sobre DeWalt DW318G Sierra de calar. Si tiene alguna pregunta, primero lea atentamente el manual. Puede solicitar un manual utilizando nuestro formulario de contacto.

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus DeWalt DW318G Sierra de calar. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con DeWalt. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu DeWalt DW318G Sierra de calar en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Marca DeWalt
Modelo DW318G
Categoría Sierras de calar
Tipo de archivo PDF
Tamaño del archivo 0.2 MB

Todos los manuales para DeWalt Sierras de calar
Más manuales de Sierras de calar

Preguntas frecuentes sobre DeWalt DW318G Sierra de calar

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

¿En qué materiales puedo usar la caladora? Verificado

Debido a sus hojas intercambiables, la caladora se puede usar con casi todos los materiales. La caladora se usa sobre todo para cortar curvas y esquinas.

Ha sido de gran ayuda (435) Leer más

¿Necesito usar protección para los ojos cuando utilizo una sierra de vaivén? Verificado

Si. Pueden volar pequeñas partículas durante el aserrado. Cuando estos golpean un ojo, pueden causar daño ocular permanente. Por eso siempre es necesario usar protección para los ojos.

Ha sido de gran ayuda (209) Leer más

¿Puedo guardar herramientas eléctricas en un cobertizo o garaje? Verificado

En general, las herramientas eléctricas se pueden guardar en un cobertizo o en un garaje, aunque a veces haga frío allí. Sin embargo, para prolongar la vida útil de la herramienta eléctrica, es mejor guardarla en un lugar seco y sin grandes fluctuaciones de temperatura. En un cobertizo o garaje, las diferencias de temperatura pueden provocar la formación de condensación, lo que puede provocar oxidación. Además, las herramientas que funcionan con baterías duran menos y no se cargan tan bien a temperaturas muy bajas. Para estar seguro de cómo debe almacenarse su herramienta eléctrica, lea siempre detenidamente el manual del usuario.

Ha sido de gran ayuda (57) Leer más

¿Necesito usar protección auditiva cuando uso una sierra de calar? Verificado

Si deberías. Aunque la cantidad de ruido producido por una sierra de calar puede variar según las marcas y modelos, la exposición prolongada a ruidos fuertes puede causar daños auditivos permanentes. Por eso es una buena idea usar protección auditiva.

Ha sido de gran ayuda (34) Leer más
Manual de uso DeWalt DW318G Sierra de calar

Productos relacionados

Categorias relacionadas