Manual de uso Emerson 1F83C-11PR Termostato

Manual de uso

3

1.) Gas/Elec Switch

If the system is a heat pump or electric furnace, the GAS/ELEC Switch must be set to

Elec. If your system is a gas or oil furnace, the switch must be set to Gas.

2.) O/B Terminal Switch

The O/B switch on this thermostat is factory set to the O position. This will accommodate

the majority of heat pump applications, which require the changeover relay to be

energized in Cool. If the heat pump being installed requires a B terminal, to energize the

changeover relay in Heat, the O/B switch must be moved to the B position.

3.) RC/RH Jumper Wire

This thermostat electrically connects the RC and RH terminals so a jumper wire is not

required. If the application provides a separate wire for RC and RH, clip the RC/RH

jumper. This will isolate both terminals so they can be independently used.

INSTALLER MENU

To prevent changes that may aect system performance, this thermostat has an INSTALLER’S

MENU and an USER MENU. The INSTALLER’S MENU provides access to every option, while

the USER MENU provides access to items that will not aect system performance. To access

the INSTALLER’S MENU press the Menu button for 8 seconds. The display will show item 30 in

the table below. Use Next and Back to navigate through menu items. Press or to change

a menu setting.

Installer’s Menu #

(Hold Menu 8 Seconds)

Description

Default Setting

(ashing icons)

Settings

(Press or )

30

Heat Cycle Rate (how often

the heat will turn on)

MEd

SLO – slow

MEd – medium

FAS – fast

35

Cool Cycle Rate (how often

the cooling will turn on)

MEd

SLO – slow

MEd – medium

FAS – fast

50

Compressor Lockout

(protects the compressor

from short cycling)

OFF

On – 5 minute display

OFF – no delay

65

Maximum Heat Limit

(maximum set point for heat mode)

99 47 to 99

66

Minimum Cool Limit (minimum

set point for cool mode)

45 45 to 97

74

Schedule Type (set as either 7-Day,

5-1-1 Day or Non-Programmable)

5

7 – 7 Day

5 – 5-1-1 Day

0 – Non Programmable

(Installer Menu continued on next page)

1

3

2

Baery Locaon

Premium AA alkaline batteries

are required when C-wire is

not available. When C-wire is

available, the batteries provide

a back-up source of power (this

will maintain the clock in the

event of a power outage).

4

Installer’s Menu #

(Hold Menu 8 Seconds)

Description

Default Setting

(ashing icons)

Settings

76

Early Start (starts heating or

cooling early so your programmed

temperature is reached by the

programmed time)

OFF

On – start early

OFF – start at program

period time

79

Fahrenheit or Celsius °F

°F – Fahrenheit

°C – Celsius

81

Temperature Display

Adjustment (adjust the displayed

“Room Temperature”)

0 -5 to +5

83

Continuous Display Light (keep

the backlight always on – “C” wire

required)

OFF

On – always on

OFF – momentarily

86

Change Air Filter (set up a

monthly reminder)

OFF

1 to 12 – reminder time

(months)

OFF – no lter reminder

99

Keypad Lock (prevent unwanted

changes to the thermostat)

OFF

On – disable buttons

OFF – all buttons are

active

INSTALLER MENU (C0ntinued)

TEST EQUIPMENT

Turn on power to the system.

Fan Operation

If your system does not have a G terminal connection, skip to Heating System.

1.) Move fan switch to On position. The blower should begin to operate.

2.) Move fan switch to Auto position. The blower should stop immediately.

Heating System

1.) Move System Switch to Heat position.

2.) Press to adjust thermostat setting to 1° above room temperature. The system should

begin to operate and the thermostat will indicate Heat On.

3.) Press to adjust thermostat setting 1° below room temperature. The heating system

should stop operating and the thermostat should indicate Heat.

Cooling System

1.) Move System Switch to Cool position.

2.) Press to adjust thermostat setting 1° below room temperature. The blower should

come on immediately on high speed, followed by cold air circulation. The thermostat will

indicate Cool On. There can be up to a 5 minute delay. (see INSTALLER MENU, item 50)

3.) Press to adjust thermostat setting to 1° above room temperature. The cooling system

should stop operating and the thermostat will indicate Cool.

Note: If Starting Soon is shown on the display, the compressor lockout feature is operating.

There will be up to a 5 minute delay before the compressor turns on.(see INSTALLER MENU,

item 50)

CAUTION

!

To prevent compressor and/or property damage, if the outdoor temperature is below 50°F,

DO NOT operate the cooling system.

Do not allow the compressor to run unless the compressor oil heaters have been operational

for 6 hours and the system has not been operational for at least 5 minutes.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Emerson 1F83C-11PR Termostato. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Emerson. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Emerson 1F83C-11PR Termostato en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Emerson Termostatos
Más manuales de Termostatos

Preguntas frecuentes sobre Emerson 1F83C-11PR Termostato

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Emerson 1F85U-42NP Termostato

Manual de uso

Emerson 1F85U-22NP Termostato

Manual de uso

Emerson 1F85U-22PR Termostato

Manual de uso

Emerson 1F83H-21NP Termostato

Manual de uso

Emerson 1F85U-42PR Termostato

Manual de uso

Emerson 1F83H-21PR Termostato

Manual de uso

BTicino NT4448 Termostato

Manual de uso

Danfoss RET 2000M Termostato

Categorias relacionadas