Manual de uso Graco 2M18 Direct Connect Vigilabebés

¿Necesita un manual para su Graco 2M18 Direct Connect Vigilabebés? A continuación puedes ver y descargar el manual en PDF gratis en español. Este producto actualmente tiene 2 preguntas frecuentes, 0 comentarios y tiene 0 votos. Si este no es el manual que desea, , contáctenos.

¿Su producto tiene algún defecto y el manual no ofrece ninguna solución? Vaya a Repair Café para solicitar un servicio de reparación gratuito.

Manual de uso

Loading…

Parent Unit
• The battery must be plugged into the Parent
Unit before the unit will be ready for use.
Remove the battery door cover on the Parent
Unit with a key or flat blade screwdriver. Remove
the battery pack from the packaging and plug
into the back of the unit. Place the battery pack
into the recess and press the wire into the slot
on the side. Replace the battery door.
Nursery Unit
• Turn the unit over, and use Phillips screwdriver
to remove the battery door.
• Place 3-AAA (1.5V-LR03) batteries into the
battery compartment. Note the proper
orientation of the batteries.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon zinc), or
rechargeable (ni-cadmium, etc) batteries.
• Place the battery door back on the unit.
• Please remove a dead battery promptly.
A dead battery left in the unit may leak,
damaging your unit.
• Do not attempt to recharge a non-rechargeable
battery.
• A rechargeable battery CANNOT be recharged by plugging the AC adapter into the Nursery Unit.
• Remove the batteries from the unit if it is no longer being used or will be stored for an extended period
of time.
• The Parent Unit(s) can use either the rechargeable battery that comes with the unit or standard 120 volt
AC household current. The Nursery Unit uses 3-AAA (1.5V-LR03) batteries or standard 120 volt AC
household current.
• To use AC adapters, plug the connector on the cord into the AC adapter jack on the side of the Parent
Unit and the back of the Nursery Unit. Then plug adapter into a standard wall outlet.
• Use ONLY the Graco adapters included with the unit. Do not use these adapters with other equipment
under any circumstances.
• If units do not work, check that AC adapters are plugged into working outlets.
• When electricity is off (from a power failure, etc.), the Nursery Unit will operate on 3-AAA (1.5V-LR03)
batteries. If the Power LED is not lit, turn the power off and then back on to the Nursery Unit. A green
LED indicates that the batteries are fine. A red LED indicates that the batteries are low. If the LED does
not light at all, then replace the batteries. The Parent Unit will operate if the rechargeable battery is
charged.
Battery Installation
Using AC Adapters
Plug in cord
3
Batteries should be disposed of properly
by recycling.
• Remove and discard static cling labels.
Static Cling Labels
• In case you are experiencing some interference, the channel on the Nursery Unit can
be changed by pressing the “ch” button on the front of the unit. The Parent Unit will
automatically scan all of the available channels until it locks on to the Nursery Unit.
If you are still experiencing interference, press the channel button on the front of the
Nursery Unit up to 6 times until a good channel is found.
Selecting Channels
Descargue el manual en Español (PDF, 0.97 MB)
(Piense en el medioambiente y solo imprima este manual si es de verdad necesario)

Loading…

Puntuación

Dé su opinión de la Graco 2M18 Direct Connect Vigilabebés calificando el producto. ¿Quiere compartir su experiencia con este producto o hacer una pregunta? Deje un comentario en la parte inferior de la página.
¿Estás satisfecho con elGraco 2M18 Direct Connect Vigilabebés?
No
Sea el primero en calificar este producto
0 votos

Únase a la conversación sobre este producto

Aquí puedes compartir lo que piensas sobre Graco 2M18 Direct Connect Vigilabebés. Si tiene alguna pregunta, primero lea atentamente el manual. Puede solicitar un manual utilizando nuestro formulario de contacto.

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Graco 2M18 Direct Connect Vigilabebés. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Graco. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Graco 2M18 Direct Connect Vigilabebés en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Marca Graco
Modelo 2M18 Direct Connect
Categoría Vigilabebés
Tipo de archivo PDF
Tamaño del archivo 0.97 MB

Todos los manuales para Graco Vigilabebés
Más manuales de Vigilabebés

Preguntas frecuentes sobre Graco 2M18 Direct Connect Vigilabebés

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

¿Por qué el alcance del monitor para bebés es menor que el descrito en el folleto/manual? Verificado

Las marcas suelen indicar un alcance basado en un uso sin obstáculos, como paredes o una distancia que abarque varias plantas. Si el alcance es insuficiente, intente ubicar el monitor para bebés con el mínimo de obstáculos posibles.

Ha sido de gran ayuda (657) Leer más

Cuando escucho a mi bebé puedo oír claramente su respiración, pero no la oigo a través del vigilabebés. ¿Por qué? Verificado

Se debe a la sensibilidad del vigilabebés. Ajuste la configuración para aumentar la sensibilidad y captar los sonidos más silenciosos.

Ha sido de gran ayuda (336) Leer más
Manual de uso Graco 2M18 Direct Connect Vigilabebés

Productos relacionados

Categorias relacionadas