Manual de uso Hikoki G 18DBBL Amoladora angular

Manual de uso

5

English

– Check that the work piece is properly supported;

– Do not use cutting off wheel for side grinding;

– Ensure that sparks resulting from use do not create

a hazard e.g. do not hit persons, or ignite fl ammable

substances;

– Ensure that ventilation openings are kept clear when

working in dusty conditions, if it should become

necessary to clear dust, fi rst disconnect the tool from

the mains supply (use non metallic objects) and avoid

damaging internal parts;

– Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves, helmet

and apron should be worn;

– Pay attention to the wheel that continues to rotate after

the tool is switched off .

– Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

– Never disassemble the rechargeable battery and

charger.

– Never short-circuit the rechargeable battery.

Shortcircuiting the battery will cause a great electric

current and overheat. It results in burn or damage to the

battery.

– Do not dispose of the battery in fi re. If the battery is burnt,

it may explode.

– Do not insert object into the air ventilation slots of the

charger. Inserting metal objects or infl ammables into the

charger air ventilation slots will result in electrical shock

hazard or damaged charger.

– Bring the battery to the shop from which it was purchased

as soon as the post-charging battery life becomes too

short for practical use. Do not dispose of the exhausted

battery.

ADDITIONAL SAFETY WARNINGS

1. Ensure that the depressed center wheel to be utilized is

the correct type and free of cracks or surface defects.

Also ensure that the depressed center wheel is properly

mounted and the wheel nut is securely tightened.

2. Confi rm that the push button is disengaged by pushing

push button two or three times before switching the

power tool on.

3. To prolong the life of the machine and ensure a fi rst

class fi nish, it is important that the machine should not

be overloaded by applying too much pressure. In most

applications, the weight of the machine alone is suffi cient

for eff ective grinding. Too much pressure will result in

reduced rotational speed, inferior surface fi nish, and

overloading which could reduce the life of the machine.

4. The wheel continues to rotate after the tool is switched

off .

After switching off the machine, do not put it down until

the depressed center wheel has come to a complete

stop. Apart from avoiding serious accidents, this

precaution will reduce the amount of dust and swarf

sucked into the machine.

5. When the machine is not use, the power source should

be disconnected.

6. Be sure to switch OFF and disconnect the attachment

plug from the receptacle to avoid a serious accident

before the depressed center wheel is assembling and

disassembling.

7. Be careful of brake kickback.

This cordless disk grinder features an electric brake that

functions when the switch is released. As there is some

kickback when the brake functions, be sure to hold the

main body securely.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the

protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the motor

stops.

In such a case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes of

overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand, please

be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○ During work make sure that swarf and dust do not fall on

the battery.

○ Make sure that any swarf and dust falling on the power

tool during work do not collect on the battery.

○ Do not store an unused battery in a location exposed to

swarf and dust.

○ Before storing a battery, remove any swarf and dust that

may adhere to it and do not store it together with metal

parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject the

battery to severe physical shock.

3. Do not use an apparently damaged or deformed battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

specifi ed.

7. If the battery charging fails to complete even when a

specifi ed recharging time has elapsed, immediately stop

further recharging.

8. Do not put or subject the battery to high temperatures or

high pressure such as into a microwave oven, dryer, or

high pressure container.

9. Keep away from fi re immediately when leakage or foul

odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears abnormal

during use, recharging or storage, immediately remove it

from the equipment or battery charger, and stop use.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you fi nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using the

battery for the fi rst time, do not use and return it to your

supplier or vendor.

0000Book̲G18DBBL.indb50000Book̲G18DBBL.indb5 2017/12/0113:15:452017/12/0113:15:45

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Hikoki G 18DBBL Amoladora angular. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Hikoki. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Hikoki G 18DBBL Amoladora angular en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Hikoki Amoladoras angulares
Más manuales de Amoladoras angulares

Preguntas frecuentes sobre Hikoki G 18DBBL Amoladora angular

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Hikoki G 3613DA Amoladora angular

Manual de uso

Hikoki G 10SS2 Amoladora angular

Manual de uso

Hikoki G 3623DA Amoladora angular

Manual de uso

Hikoki G 10SQ2 Amoladora angular

Manual de uso

Hikoki G 18DSL2 Amoladora angular

Manual de uso

Hikoki G 23MRUA Amoladora angular

Manual de uso

Hikoki G 18DL(S) Amoladora angular

Manual de uso

Hikoki G 23SU Amoladora angular

Categorias relacionadas