Manual de uso Hoover FL700 011 Limpiador de vapor

Manual de uso

2

GB

GETTING TO KNOW YOUR CLEANER USING YOUR CLEANER

ASSEMBLING YOUR CLEANER

A. Soft Hand Grip

B. ON/OFF Switch

C. Solution Trigger: squeeze to release cleaning solution

D. Mode Selector Dial: turns brushes ON for wet washing and OFF for drying and vacuuming

E. Clean Water Solution Tank Cap/Measuring Cup

F. Clean Water Solution Tank

G. Clean Water Solution Tank Release

H. Dirty Water Tank Release

I. Dirty Water Tank Lid and Filter

J. Dirty Water Tank: collects dry debris as well as dirty cleaning solution

K. Nozzle Release Buttons: release nozzle for easy clean-up (located behind nozzle)

L. Nozzle

M. Squeegee (underneath nozzle)

N. Bumper

O. Soft-tread Wheels

P. Carrying Handle

Q. Upper Handle Release Button

R. Cord Hooks: top hook rotates for quick cord release

S. Handle Release Pedal

Remove all components from the packaging.

Install Brushes and Nozzle

1. To install brushes, place handle in upright position. Tilt cleaner back so that it rests on

the oor. Align post (a) on brush block with hole (b) on bottom of cleaner. Turn brushes

slightly until post ts easily into hole. [2]

2. Press brush assembly rmly to snap into place. [3]

3. To install nozzle, make sure latches (c) are out. Align middle section (d) of nozzle with

opening (e) on cleaner. Remove cardboard packing insert from squeegee area on

underside of nozzle. [4]

4. While holding nozzle in place, slide latches inward to lock in place. [5]

Unfold / Fold the Handle

1. Raise upper handle to upright position until it locks in place. [6]

2. Press upper handle release button to fold handle to storage position. [7]

BEFORE YOU BEGIN CLEANING

Clean Water Tank Solution

The Clean Water Solution Tank holds detergent and water that is to be dispersed onto the

surface being cleaned.

1. Turn cleaner o and disconnect from electrical outlet.

2. Place carpet cleaner handle in the upright, locked position. [6]

3. To remove tank, squeeze release button and pull tank straight out. [8]

4. Rotate tank cap counter-clockwise and lift up to remove cap (a). [9]

5. Turn cap (b) upside down to serve as a measuring cup. [10]

6. For hard surface oors such as vinyl, linoleum, marble, laminate wood, polyurethane

sealed wood or other wood oors that can normally be cleaned using water, use one cup

(60ml) of low foam producing oor detergent.

7. Pour cleaning detergent into tank (c). Fill tank to ll line (d) with warm water. [11]

8. If rubber ring (e) on cap has become dislodged, reposition it with uneven side against

ledge (f) as shown. [12]

9. Replace cap. Rotate cap clockwise until it locks in place. Cap must be locked in place for

proper performance and to prevent leaking.

10. Slide tank straight into position until latch snaps in place.

Note: Check for worn spots or joint separations before using, as these conditions could lead to

damaged ooring when using water to clean oor.

IMPORTANT: Do not use cleaning concentrates that contain solvent based ingredients.

Cleaning Floors

Recommended cleaning sequence:

VACUUM: Vacuum to remove loose dirt, hair and debris.

WASH: Clean the oor surface. The brushes will provide light agitation to help loosen dirt.

DRY: Pickup reduces drying time of the oor surface.

1. Set Mode selector dial to VACUUM position and vacuum oor. [1D]

2. Fill Clean Water Solution Tank with either oor cleaning detergent and water.

3. Turn Mode selector dial to WASH position. [1D]

4. Dry hands and plug cleaner into a properly grounded outlet.

5. Step on handle release pedal and lower handle to operating position. [15] Turn cleaner

ON. [1B]

6. To release solution, squeeze trigger. Slowly move cleaner forward and backward over

area to be cleaned. Squeeze trigger to release solution as needed. [16]

7. Overlap strokes by one inch to help prevent streaking. The cleaner’s suction will pick up

the dirty solution throughout cleaning.

FloormateManual__1-4_union.indd 2 10/09/2012 14.00.11

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Hoover FL700 011 Limpiador de vapor. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Hoover. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Hoover FL700 011 Limpiador de vapor en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Hoover Limpiadoras de vapor
Más manuales de Limpiadoras de vapor

Preguntas frecuentes sobre Hoover FL700 011 Limpiador de vapor

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Hoover SSNC1700 011 Steamjet Limpiador de vapor

Manual de uso

Hoover SCB1500 011 Limpiador de vapor

Manual de uso

Hoover JWC60B6/1 011 Limpiador de vapor

Manual de uso

Hoover S2IN1300 011 Steamjet Limpiador de vapor

Manual de uso

Hoover SSNH1300 011 Steamjet Handy Limpiador de vapor

Manual de uso

Hoover S2IN1300C 001 Steamjet Limpiador de vapor

Manual de uso

Hoover CAD1700D 011 Limpiador de vapor

Manual de uso

Hoover S2IN1300 001 Steamjet Limpiador de vapor

Categorias relacionadas