Manual de uso Hozelock 1585A Aquaforce 12000 Bomba de la fuente

Manual de uso

8

1. When the pump is newly installed, you should

check your pump daily that it is performing

correctly.

2. If you notice a drop in performance (low flow) you

should clean the strainer cage. Cleaning intervals

will vary depending on the condition of your pond’s

water. This could be as often as weekly in the

summer months. To clean the strainer cage, open

the clips and remove the pump. The cage can then

be wiped clean of debris blocking the strainer holes

and washed in clean water. You should also check

that the pump chamber & rotor are not blocked

with debris.

3. At least once a year you should completely

disassemble the pump including the rotor assembly

as described below and wash all components in

clean, fresh water.

Replace worn or broken parts.

4. If you live in a hard water area (water with high

levels of calcium or limescale content), the pump,

rotor assembly and steel can should be cleaned

at regular intervals. The cleaning interval required

will vary depending on the hardness of your water,

so you should inspect for signs of calcium build up

regularly.

To clean off calcium or limescale deposits a small

nylon bristled brush (such as a toothbrush) may be

used.

Dismantle the pump as described above and

remove the rotor. Clean the limescale deposits

from the rotor using fresh clean water If

excessive calcium deposits build up, the thermal

overload protection may be activated (See

INTRODUCTION).

Pump Dismantling & Assembly

(6000 & 8000) - Fig 22 & 24

1. Switch off the pump and remove the strainer cage

as described above and remove the pump.

2. Ensure the pump is cool before dismantling it.

3. Unscrew the 4 posidrive screws (a) from the

chamber.

4. Gently pull the pump chamber (b) squarely away

from the motor body (e).

5. Pull the rotor assembly (c) out of the motor body.

Important! Take extra care so as to not drop the

rotor assembly.

6. Wash out all of the components in clean water. Do

not use detergents or other chemical cleaners.

7. Ensure the o-ring (d) is in its groove (Fig 24a &

24b).

8. Replace the rotor assembly into the motor body

ensuring that the holes in the plate behind the

impeller locate onto the pins on the motor body

(Fig 24c & 24d).

9. Refit the pump chamber. Twist the chamber to

align the screw holes and refit the screws taking

care not to push out the nuts in the motor body

(Fig 24e).

10. Return the pump to the strainer cage.

Pump Dismantling & Assembly

(12000 & 15000) - Fig 23 & 25

1. Switch off the pump and remove the strainer cage

as described above and remove the pump.

2. Ensure the pump is cool before dismantling it.

3. Unscrew the 4 posidrive screws (a) from the

chamber.

4. Rotate and pull the pump chamber (b) squarely

away from the motor body (e).

5. Pull the rotor assembly (c) out of the motor body.

Important! Take extra care so as to not drop the

rotor assembly.

6. Wash out all of the components in clean water. Do

not use detergents or other chemical cleaners.

7. Replace the rotor assembly into the motor body

(Fig 25a), ensuring that the holes in the plate

behind the impeller locate onto the pins on the

motor body (fig 25b).

8. Note that the o-ring groove is formed when the

rotor has been correctly positioned (Fig 25c). Fit

the o-ring (d) over the rotor. Ensure the o-ring is on

correctly positioned between the rotor plate and

motor body (Fig 25d).

9. Refit the pump chamber. Twist the chamber to

align the screw holes and refit the screws taking

care not to push out the nuts in the motor body

(Fig 25e).

10. Return the pump to the strainer cage.

Winter Care

1. Your pump should be removed from your pond

during the autumn.

2. Clean the pump as described above.

3. During winter, we recommend storing the pump in

a bucket of water. This is to prevent the bearings

from drying out and potentially seizing. This is

especially important if you have been using your

pump in a hard water area. The bucket of water

containing the pump should be stored in a frost

protected area.

Troubleshooting/Fault Finding

Important - Please keep this section for reference.

LOW FLOW FROM PUMP

1. Ensure that the strainer cage is clean.

2. A small diameter outlet pipe will restrict outlet

flow.

3. Ensure that there is no blockage within the pump

chamber.

4. If using the pump amphibiously, ensure that the

ball joint is not being used and check that the

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Hozelock 1585A Aquaforce 12000 Bomba de la fuente. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Hozelock. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Hozelock 1585A Aquaforce 12000 Bomba de la fuente en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Hozelock Bombas de la fuentes
Más manuales de Bombas de la fuentes

Productos relacionados

Manual de uso

Hozelock 1766 EasyClear 7500 Bomba de la fuente

Manual de uso

Hozelock 1768 EasyClear 9000 Bomba de la fuente

Manual de uso

Hozelock 1582 Aquaforce 4000 Bomba de la fuente

Manual de uso

Hozelock 1584A Aquaforce 8000 Bomba de la fuente

Manual de uso

Hozelock 1760 EasyClear 3000 Bomba de la fuente

Manual de uso

Hozelock 3352 Cascade 700 Bomba de la fuente

Manual de uso

Hozelock 1586A Aquaforce 15000 Bomba de la fuente

Manual de uso

Hozelock 3303 Cascade 450 Bomba de la fuente

Categorias relacionadas