Manual de uso Klip Xtreme KLS-700 Magno Altavoz

Manual de uso

VI. Advanced operation

Pairing the speaker with wireless devices

VII. Troubleshooting

3. FM radio mode

2. USB/MicroSD

TM

playback

a. Insert a MicroSD

TM

card or USB memory stick into the corresponding slot.

b. The device will automatically play any music in MP3 format stored on the memory.

1. Press the MODE button briefly to toggle through the available audio sources and select FM.

2. Press the SCAN button to start scanning for radio stations automatically, in the frequency range between

87.5 and 108.0MHz.

3. Once the search is complete, the unit will save active stations automatically.

4. Use the and to select stored channels.

Note: Before installing this product, please make sure your device is compatible with Bluetooth

®

V5.0.

1. Enable the Bluetooth

®

feature on the selected source and set it to discover the wireless speaker.

2. Place your wireless device and the speaker not more than one meter away from each other.

3. Next, cycle to the Bluetooth

®

feature on the speaker by pressing the MODE button found on the main

unit or the remote control and select it as the input source. The BT symbol blinks fast on the display to

indicate that the speaker has entered into the pairing mode.

4. Once the speaker appears listed (KLS-901) under the newly found Bluetooth

®

devices of your wireless

device, it will ask if you want to pair with it.

5. Accept by pressing Yes or Ok. If you have a lower Bluetooth

®

version, you may be prompted to enter

the passkey 0000 (4 zeros).

6. When pairing is successful, the BT symbol stops blinking indicating that the wireless connection has been

established. If after 60 seconds the pairing process fails, please repeat steps 1 through 5 described above.

7. You can now start streaming audio through the speaker wirelessly from your favorite Bluetooth

®

-

enabled devices.

8. The speaker will re-pair automatically to the memorized device when the BT mode is selected on the

unit after being turn off and on again.

Technical specifications

Device

MPN KLS-700

Type

Peak Maximum Power Output (PMPO)

Maximum power output (Rated RMS)

Maximun AC input (current/voltage)

Maximun DC input (current/voltage)

Buttons and knobs

Speaker

Driver unit

Maximum power output (RMS)

Frequency

Impedance

Sensitivity

Signal to noise ratio

Total Harmonic Distortion (THD)

Loudspeaker system Bluetooth® compatible

2000W

180W

110V-240V(±10%) 60/50Hz (autosensing)

5V/1A

GT. VOL., MIC. ECHO, MIC. DELAY, MIC. VOL., MASTER

VOLUME KNOB, EQ CONTROLS, MODE, BT, LIGHT,

REPEAT, SWITCH ON/OFF, PREV. TRACK, NEXT TRACK,

SCAN/TUNE-, PLAY/TUNE +

One 12in + Two 1in

120W + 60W

Subwoofer: 20Hz-100Hz

Speakers: 120Hz-20KHz

12in: 4Ω

1in: 8Ω

83dB±3dB

≥70dB

1kHz, 0dB (±10%)

Status Possible cause Solution

The display fails to

turn on

No sound

The speaker is not connected properly

Power switch not on

Volume adjusted at the lowest level

Wrong input mode selected

Check the connection and plug in the AC adapter

Turn on the power switch

Adjust the volume to a comfortable listening level

Choose the playback mode based on the

external source being used

Status Possible cause Solution

Distorted sound

High-pitched whistling

noise when using the

microphone

Too much bass

Master volume is too high

The speaker is damaged

Bass level needs adjustment

Feedback

Decrease the master volume. You can also try

lowering the volume of the source device or

musical instrument. Adjust EQ settings.

Check or replace the speaker

Adjust the EQ control from the speaker or the

source device

Point the microphone away from the speaker

Microphone is not heard

over the music volume

Volume coming from the source device is

too loud

Turn down the music volume coming from the

source device

PREV or NEXT fails to

tune to the previous or

next radio station

Signal reception is not strong enough Press Mode until Tuner is selected, then press

the Scan button to scan radio station

automatically. Press Prev or Next to go back or

forward in the dial.

Radio station channel is

flashing

Blue icon blinks fast

Blue icon blinks slowly

USB track number (e.g. 001) blinks slowly

The unit is currently in Bluetooth

®

pairing mode.

Bluetooth

®

music playback is muted. Unmute to resume

playback.

The audio coming from the USB drive is muted. Unmute to

stop the track indication from flashing and resume playback.

The unit is currently muted. Unmute the speaker to stop the LED from

flashing and resume playback.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Klip Xtreme KLS-700 Magno Altavoz. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Klip Xtreme. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Klip Xtreme KLS-700 Magno Altavoz en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Klip Xtreme Altavoces
Más manuales de Altavoces

Preguntas frecuentes sobre Klip Xtreme KLS-700 Magno Altavoz

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Klip Xtreme KSB-250 MystiK Altavoz

Manual de uso

Klip Xtreme KSS-310 StereoBytes Altavoz

Manual de uso

Klip Xtreme KWS-614BK RefleXion Altavoz

Manual de uso

Klip Xtreme KWS-015 Zound360 Altavoz

Manual de uso

Klip Xtreme KWS-614GD RefleXion Altavoz

Manual de uso

Klip Xtreme KBS-750 Adamant Altavoz

Manual de uso

Klip Xtreme KSB-500 Zaffire Altavoz

Manual de uso

Klip Xtreme KSB-200 Baton Altavoz

Categorias relacionadas