Manual de uso König KN-URC10B Control remoto

Manual de uso

12

6) Test the functionality of your remote control using the TV standby button ( ) and the AV button (

av

). If the TV

set responds properly to all functions, your KN-URC10B is correctly programmed and can be used.

Note

:

It could happen, that during the search process, the KN-URC10B fi nds several codes to which your TV set

responds, but where all buttons do not function for each code. In this case, the search process should be

re-started (steps 2 to 6) until you obtain the best code. Re-starting the search process starts at the last saved

programming.

Code reader

The code reader can be used to display the codes that you have found in the search process so that you can

make a note of them:

1) Press and hold the TV Standby button (

) until the LED Signal ( ) fl ashes twice.

2) Use the number buttons to enter the code 0 0 0 2. The Signal LED (

) fl ashes twice again.

3) Push 1 and count the number of times the Signal LED fl ashes; this is the fi rst number.

4) Push 2 and count the number of times the Signal LED fl ashes; this is the second number.

5) Push 3 and count the number of times the Signal LED fl ashes; this is the third number.

6) Push 4 and count the number of times the Signal LED fl ashes; this is the fourth number.

Note

:

The Signal LED does not fl ash if the number is 0. The steps 3 to 6 can be carried out in any order and as many

times as may be required.

Learn feature

Alternatively, or if either in case of manual programming or with automatic programming, the correct code for your

equipment cannot be found, you may use the learn feature.

The learn feature may also be used if certain button functions of the original remote control are not included in the

database.

Positioning the KN-URC10B and original remote control (Range test)

In order to ensure that the remote control can receive the signal, both remote controls should be placed opposite

one another with their transmission diodes facing each other. The distance between both remote controls should

not be greater than 5 cm.

You may use the range test to determine the optimal position for learning the codes:

1) Press and hold the TV Standby button (

) until the LED Signal ( ) fl ashes twice.

2) Enter the code 0 0 1 1 using the numeric buttons. The signal LED fl ashes twice again.

3) Now, the signal LED lights up in orange and displays the quality of the signals received.

Now place the original remote control and press and hold any button on it.

Change the distance to the KN-URC10B remote control until the signal LED lights up in green.

Note

:

Orange light indicates readiness and that the KN-URC10B is not receiving any signal.

If the signal LED lights up in red, it means that the signal is too weak (too far away) or too strong (too near).

If the signal LED lights up in green, it indicates optimal signal quality (optimal alignment for learning).

4) To end the range test, press the TV Standby button (

) that had been pressed earlier.

Note

:

The optimal alignment depends on the transmission strength of the signals by the original remote control and,

hence, it may vary for each remote control. This is why you need to carry out the range test with each remote

control from which you would like to learn in order to determine the optimal alignment for it.

Learning – Basic

1) Press and hold the TV Standby button (

) until the LED Signal ( ) fl ashes twice.

2) Enter the code 0 0 0 9 using the numeric buttons. The signal LED fl ashes twice again.

3) Now, the signal LED lights up in green.

4) Press the button on the KN-URC10B remote control that you would like to teach, e.g. OK (

ok

).

5) The signal LED lights up in orange and indicates that the KN-URC10B remote control is ready to learn.

6) Press and hold the desired button on the original remote control until the green signal LED goes off.

BA König KN-URC10B, 135x215 mm, Entwurf 02 CS6.indd 12BA König KN-URC10B, 135x215 mm, Entwurf 02 CS6.indd 12 12.09.2012 08:36:0312.09.2012 08:36:03

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus König KN-URC10B Control remoto. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Konig. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu König KN-URC10B Control remoto en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para König Controles remotos
Más manuales de Controles remotos

Preguntas frecuentes sobre König KN-URC10B Control remoto

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

König KN-URC40B Control remoto

Manual de uso

König KN-URC80B Control remoto

Manual de uso

König CMP-MEDIAREM12 Control remoto

Manual de uso

König KN-RCU10B Control remoto

Manual de uso

König KN-URC20B Control remoto

Manual de uso

Thomson ROC2411 Control remoto

Manual de uso

Hama 00221040 Control remoto

Manual de uso

Philips SRT9320 Control remoto

Categorias relacionadas