Manual de uso Makita 9561Z Amoladora angular

Manual de uso

ENGLISH

Explanation of general view

1 Wheel cover

2 Bearing box

3 Screw

4 Press

5 Shaft lock

6 Lock nut

7 Depressed center wheel

8 Inner flange

9 Lock nut wrench

10 Switch lever

11 Exhaust vent

12 Inhalation vent

SPECIFICATIONS

9560Z 9561Z 9562Z 9563Z 9564Z 9565Z

Depressed center wheel diameter 100 mm 115 mm 125 mm 100 mm 115 mm 125 mm

Spindle thread M10 M14 M14 M10 M14 M14

No load speed (min

-1

) 11,000 11,000 11,000 11,000 11,000 11,000

Overall length 289 mm 289 mm 289 mm 299 mm 289 mm 299 mm

Net weight 1.7 kg 1.7 kg 1.7 kg 1.8 kg 1.8 kg 1.8 kg

•

Due to our continuing program of research and develop-

ment, the specifications herein are subject to change with-

out notice.

•

Note: Specifications may differ from country to country.

Power supply

The machine should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can only

be operated on single-phase AC supply. They are double-

insulated in accordance with European Standard and can,

therefore, also be used from sockets without earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES ENB031-4

1. Always use eye and ear protection. Other personal

protective equipment such as dust mask, gloves,

helmet and apron should be worn when necessary. If

in doubt, wear the protective equipment.

2. Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

3. Keep guards in place.

4. Use only wheels with correct size and wheels having

a maximum operating speed at least as high as the

highest No Load Speed marked on the tool’s name-

plate.When using depressed center wheels, be sure

to use only fiberglass-reinforced wheels.

5. Check the wheel carefully for cracks or damage

before operation. Replace cracked or damaged wheel

immediately.

6. Observe the instructions of the manufacturer for

correct mounting and use of wheels. Handle and

store wheels with care.

7. Do not use separate reducing bushings or adaptors

to adapt large hole abrasive wheels.

8. Use only flanges specified for this tool.

9. Do not damage the spindle, the flange (especially the

installing surface) or the lock nut. Damage to these

parts could result in wheel breakage.

10. For tools intended to be fitted with threaded hole

wheel, ensure that the thread in the wheel is long

enough to accept the spindle length.

11. Before using the tool on an actual workpiece, test run

the tool at the highest no load speed for at least 30

seconds in a safe position. Stop immediately if there

is any vibration or wobbling that could indicate poor

installation or a poorly balanced wheel. Check the

tool to determine the cause.

12. Check that the workpiece is properly supported.

13. Hold the tool firmly.

14. Keep hands away from rotating parts.

15. Make sure the wheel is not contacting the workpiece

before the switch is turned on.

16. Use the specified surface of the wheel to perform the

grinding.

17. Do not use cutting off wheel for side grinding.

18. Watch out for flying sparks. Hold the tool so that

sparks fly away from you and other persons or

flammable materials.

19. Pay attention that the wheel continues to rotate after

the tool is switched off.

20. Do not touch the workpiece immediately after opera-

tion; it may be extremely hot and could burn your

skin.

21. Position the tool so that the power cord always stays

behind the tool during operation.

22. If working place is extremely hot and humid, or badly

polluted by conductive dust, use a short-circuit

breaker (30 mA) to assure operator safety.

23. Do not use the tool on any materials containing

asbestos.

24. Do not use water or grinding lubricant.

25. Ensure that ventilation openings are kept clear when

working in dusty conditions. If it should become

necessary to clear dust, first disconnect the tool from

the mains supply (use non metallic objects) and avoid

damaging internal parts.

SAVE THESE INSTRUCTIONS.

4

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Makita 9561Z Amoladora angular. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Makita. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Makita 9561Z Amoladora angular en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Makita Amoladoras angulares
Más manuales de Amoladoras angulares

Preguntas frecuentes sobre Makita 9561Z Amoladora angular

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Makita GA7020S Amoladora angular

Manual de uso

Makita 9563Z Amoladora angular

Manual de uso

Makita GA7030S Amoladora angular

Manual de uso

Makita 9565Z Amoladora angular

Manual de uso

Makita GA7031Y Amoladora angular

Manual de uso

Makita 9564 Amoladora angular

Manual de uso

Makita GA5040 Amoladora angular

Manual de uso

Makita DGA452 Amoladora angular

Categorias relacionadas