Manual de uso Makita GA5034 Amoladora angular

Manual de uso

4

ENGLISH (Original instructions)

Explanation of general view

1 Shaft lock

2 Lock-off lever

3 Switch lever

4 Wheel guard

5Screw

6 Bearing box

7Lever

8Lock nut

9 Depressed center grinding

wheel/ Multi-disc

10 Inner flange

11 Lock nut wrench

12 Abrasive cut-off wheel/diamond

wheel

13 Wheel guard for abrasive cut-off

wheel/diamond wheel

14 Exhaust vent

15 Inhalation vent

SPECIFICATIONS

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

ENE048-1

Intended use

The tool is intended for grinding, sanding and cutting of

metal and stone materials without the use of water.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

GEA010-1

General Power Tool Safety Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future refer-

ence.

GEB033-7

GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding,

Wire Brushing, or Abrasive Cutting-Off Operations:

1. This power tool is intended to function as a

grinder, sander, wire brush or cut-off tool. Read

all safety warnings, instructions, illustrations

and specifications provided with this power tool.

Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.

2. Operations such as polishing are not recom-

mended to be performed with this power tool.

Operations for which the power tool was not

designed may create a hazard and cause personal

injury.

3. Do not use accessories which are not specifi-

cally designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

4. The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and fly apart.

5. The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can-

not be adequately guarded or controlled.

6. Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by flanges, the arbour hole of the

accessory must fit the locating diameter of the

flange. Accessories that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

7. Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory is

dropped, inspect for damage or install an

undamaged accessory. After inspecting and

installing an accessory, position yourself and

bystanders away from the plane of the rotating

accessory and run the power tool at maximum

no-load speed for one minute. Damaged accesso-

ries will normally break apart during this test time.

Model GA4034 GA4534 GA5034

Depressed center wheel diameter 100 mm 115 mm 125 mm

Max. wheel thickness 6.4 mm 6.4 mm 6.4 mm

Spindle thread M10

M14 or 5/8"

(country specific)

M14 or 5/8"

(country specific)

Rated speed (n) / No load speed (n

0

) 11,000 min

–1

11,000 min

–1

11,000 min

–1

Overall length 265 mm 265 mm 265 mm

Net weight 1.8 kg 1.9 kg 1.9 kg

Safety class /II

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Makita GA5034 Amoladora angular. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Makita. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Makita GA5034 Amoladora angular en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Makita Amoladoras angulares
Más manuales de Amoladoras angulares

Preguntas frecuentes sobre Makita GA5034 Amoladora angular

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Makita GA7021 Amoladora angular

Manual de uso

Makita BGA452 Amoladora angular

Manual de uso

Makita GA5011 Amoladora angular

Manual de uso

Makita GA4534 Amoladora angular

Manual de uso

Makita 9563H Amoladora angular

Manual de uso

Makita 9563 Amoladora angular

Manual de uso

Makita 9524NB Amoladora angular

Manual de uso

Makita 9564HR Amoladora angular

Categorias relacionadas