Manual de uso Milwaukee 2967-21B Llave de impacto

Manual de uso

4

5

WARNING

Only use accessories specically

recommended for this tool. Others

may be hazardous.

Use only sockets and other accessories speci-

cally designed for use on impact wrenches. Other

sockets and accessories might shatter or break

causing injury.

Attaching and Removing Accessories

1/2" Impact Wrench with Pin Detent

(Cat. No. 2966-20)

1. WARNING! Remove battery to avoid starting the tool.

2. Use only the appropriate size Square Drive Sockets.

3. To attach a socket, align the hole in the accessory

with the detent pin on the anvil. Hold the detent

pin in while pushing the socket onto the anvil.

The detent pin will snap into place in the hole to

secure the socket.

4. To remove the socket, insert a nail or other thin

object into the hole in the accessory and press

in the detent pin. Pull the accessory o󰀨 the anvil.

1/2" Impact Wrench with Friction Ring

(Cat. No. 2967-20)

1. WARNING! Remove battery to avoid starting the tool.

2. Use only the appropriate size Square Drive Sockets.

3. To attach a socket, align the accessory with the

anvil and push it rmly over the retaining ring.

4. To remove the accessory, pull the accessory o󰀨

the anvil.

OPERATION

WARNING

To reduce the risk of injury, always

wear proper eye protection marked

to comply with ANSI Z87.1.

Using the Drive Control

The drive control button is used to adjust the torque,

rotation speed (RPM), and impact speed (IPM) for

the application.

To select the drive control mode:

Drive Control Button

Mode Indicator

1. Pull and release the trigger

to turn on the tool. The cur-

rent mode indicator is lit.

2. Press the drive control but-

ton to cycle through the

4 modes. When the desired

mode indicator is lit, begin

work.

Cat. No. 2966-20

Mode RPM IPM

Fastening

Torque

(ft-lbs)

Nut-Busting

Torque

(ft-lbs)

1 0 - 700 0 - 1400 Up to 350* Up to 350*

2 0 - 1300 0 - 2500 Up to 750* Up to 750*

3 0 - 2000 0 - 2700 Up to 900* Up to 1100*

FWD:

0 - 900

REV:

0 - 2000 /

0 - 750

0 - 2700 Up to 50*

†

Up to 1100*

Cat. No. 2967-20

Mode RPM IPM

Fastening

Torque

(ft-lbs)

Nut-Busting

Torque

(ft-lbs)

1 0 - 700 0 - 1300 Up to 650* Up to 650*

2 0 - 1300 0 - 2200 Up to 900* Up to 900*

3 0 - 2000 0 - 2400

Up to 1100

w/ XC5.0Ah

battery*

Up to 1200

w/ FORGE™

battery*

Up to 1500

w/ XC5.0Ah

battery*

Up to 1600

w/ FORGE™

battery*

FWD:

0 - 900

REV:

0 - 2000 /

0 - 750

0 - 2400 Up to 50*

†

Up to 1500

w/ XC5.0Ah

battery*

Up to 1600

w/ FORGE™

battery*

*Torque values depend on many factors such as state

of battery discharge, battery size, impacting time, bolt

size, etc. Always check with a torque wrench to ensure

desired torque value is achieved. This is not a precision

fastening tool.

†

Auto Shut-O󰀨 Mode

In mode, when run in reverse, the tool will spin

at the above RPM and IPM until the nut breaks free

from the joint. Then, the tool slows to 750 RPM for

better control in removing the nut.

Using the Control Switch

The control switch may be set to three positions:

forward, reverse and lock. Due to a lockout mecha-

nism, the control switch can only be adjusted when

the ON/OFF switch is not pressed. Always allow the

motor to come to a complete stop before using the

control switch.

For forward (clockwise) rotation, push in the control

switch from the right side of the tool. Check the

direction of rotation before use.

For reverse (counterclockwise) rotation, push in the

control switch from the left side of the tool. Check

direction of rotation before use.

To lock the trigger, push the control switch to the

center position. The trigger will not work while the

control switch is in the center locked position. Always

lock the trigger or remove the battery pack before

performing maintenance, changing accessories,

storing the tool and any time the tool is not in use.

Starting, Stopping and Controlling Speed

1. To start the tool, grasp the handle(s) rmly and

pull the trigger.

NOTE: An LED is turned on when the trigger is

pulled and will go o󰀨 shortly after the trigger is

released.

2. To vary the speed, increase or decrease the pres-

sure on the trigger. The further the trigger is pulled,

the greater the speed.

3. To stop the tool, release the trigger. Ensure the

tool has come to a complete stop before laying

the tool down.

FUNCTIONAL DESCRIPTION

1. Tool hanger ring (2966-20 only)

2. Handle

3. Drive control

4. Trigger (ON/OFF switch)

5. Control switch

6. LED

7. 1/2" Square drive anvil with pin detent

(2966-20 only)

8. 1/2" Square drive anvil with friction ring

(2967-20 only)

7

5

3

6

4

8

2

1

ASSEMBLY

WARNING

Recharge only with the charger

specied for the battery. For spe-

cic charging instructions, read the operator’s

manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

WARNING

Always lock the trigger or remove

the battery pack any time the tool

is not in use.

To insert the battery, slide the pack into the body

of the tool. Make sure it latches securely into place.

Attaching and Removing the Tool Hanger

1. To attach, place the hanger ring through the tool

hanger.

2. Position the tool hanger on the tool over the two

screw holes.

3. Insert the two screws. Hand tighten the screws.

4. To remove, reverse the procedure.

Impacting Techniques

The longer a bolt, screw, or nut is impacted, the

tighter it will become. To help prevent damaging the

fasteners or workpieces, avoid excessive impact-

ing. Be particularly careful when impacting smaller

fasteners because they require less impacting to

reach optimum torque.

Practice with various fasteners, noting the length of

time required to reach the desired torque. Check the

tightness with a hand-torque wrench. If the fasteners

are too tight, reduce the impacting time. If they are

not tight enough, increase the impacting time.

Oil, dirt, rust or other matter on the threads or under the

head of the fastener a󰀨ects the degree of tightness.

The torque required to loosen a fastener averages

75% to 80% of the tightening torque, depending on

the condition of the contacting surfaces.

On light gasket jobs, run each fastener down to a

relatively light torque and use a hand torque wrench

for nal tightening.

MAINTENANCE

WARNING

To reduce the risk of injury, always

unplug the charger and remove the

battery pack from the charger or tool before

performing any maintenance. Never disassemble

the battery pack, charger, or tool, except as pro-

vided in these instructions. Contact a MILWAUKEE

service facility for all other repairs.

Maintaining Tool

Keep your tool, battery pack and charger in good

repair by adopting a regular maintenance program.

Inspect your tool for issues such as undue noise,

misalignment or binding of moving parts, breakage of

parts, or any other condition that may a󰀨ect the tool

operation. Return the tool, battery pack, and charger

to a MILWAUKEE service facility for repair. After six

months to one year, depending on use, return the

tool, battery pack and charger to a MILWAUKEE

service facility for inspection.

If the tool does not start or operate at full power with

a fully charged battery pack, clean the contacts on

the battery pack. If the tool still does not work prop-

erly, return the tool, charger and battery pack, to a

MILWAUKEE service facility for repairs.

WARNING

To reduce the risk of personal in-

jury and damage, never immerse

your tool, battery pack or charger in liquid or

allow a liquid to ow inside them.

Cleaning

Clean dust and debris from any vents. Keep tool

clean, dry and free of oil or grease. Use only mild

soap and a damp cloth to clean, since certain clean-

ing agents and solvents are harmful to plastics and

other insulated parts. Some of these include gasoline,

turpentine, lacquer thinner, paint thinner, chlorinated

cleaning solvents, ammonia and household deter-

gents containing ammonia. Never use ammable or

combustible solvents around tools.

Repairs

For repairs, return the tool, battery pack and charger

to the nearest authorized service center.

ACCESSORIES

WARNING

Use only recommended accesso-

ries. Others may be hazardous.

For a complete listing of accessories, go online to

www.milwaukeetool.com or contact a distributor.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Milwaukee 2967-21B Llave de impacto. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Milwaukee. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Milwaukee 2967-21B Llave de impacto en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Milwaukee Llaves de impacto
Más manuales de Llaves de impacto

Preguntas frecuentes sobre Milwaukee 2967-21B Llave de impacto

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Milwaukee 2767-22 Llave de impacto

Manual de uso

Milwaukee 2758-22 Llave de impacto

Manual de uso

Milwaukee 2962P-20 Llave de impacto

Manual de uso

Milwaukee 2462-20 Llave de impacto

Manual de uso

Milwaukee 2854-20 Llave de impacto

Manual de uso

Milwaukee 2665-20 Llave de impacto

Manual de uso

Milwaukee 2655-20 Llave de impacto

Manual de uso

Milwaukee 2855P-20 Llave de impacto

Categorias relacionadas