Manual de uso Milwaukee 6117-30 Amoladora angular

Manual de uso

3

• Operations such as polishing are not recom-

mended to be performed with this power tool.

Operations for which the power tool was not designed

may create a hazard and cause personal injury.

• Do not use accessories which are not specically

designed and recommended by the tool manufac-

turer. Just because the accessory can be attached

to your power tool, it does not assure safe operation.

• The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than their

rated speed can break and y apart.

• The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories can-

not be adequately guarded or controlled.

• Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by anges, the arbour hole of the ac-

cessory must t the locating diameter of the

ange. Accessories that do not match the mounting

hardware of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

• Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory is

dropped, inspect for damage or install an undam-

aged accessory. After inspecting and installing

an accessory, position yourself and bystanders

away from the plane of the rotating accessory and

run the power tool at maximum no-load speed

for one minute. Damaged accessories will normally

break apart during this test time.

• Wear personal protective equipment. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and workshop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable of

stopping ying debris generated by various opera-

tions. The dust mask or respirator must be capable

of ltrating particles generated by your operation.

Prolonged exposure to high intensity noise may

cause hearing loss.

• Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment. Fragments

of workpiece or of a broken accessory may y away

and cause injury beyond immediate area of operation.

• Hold the power tool by insulated gripping sur-

faces only, when performing an operation where

the cutting tool may contact hidden wiring or its

own cord. Contact with a "live" wire may also make

exposed metal parts of the power tool "live" and could

give the operator an electric shock.

• Position the cord clear of the spinning accessory.

If you lose control, the cord may be cut or snagged

and your hand or arm may be pulled into the spinning

accessory.

• Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the power

tool out of your control.

• Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

your body.

• Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal may

cause electrical hazards.

• Do not operate the power tool near ammable

materials. Sparks could ignite these materials.

• Do not use accessories that require liquid cool-

ants. Using water or other liquid coolants may result

in electrocution or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other ac-

cessory. Pinching or snagging causes rapid stalling

of the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation at the point of

the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel that

is entering into the pinch point can dig into the surface

of the material causing the wheel to climb out or kick

out. The wheel may either jump toward or away from

the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels

may also break under these conditions.

Kickback is the result of power tool misuse and/or in-

correct operating procedures or conditions and can be

avoided by taking proper precautions as given below.

• Maintain a rm grip on the power tool and posi-

tion your body and arm to allow you to resist

kickback forces. Always use auxiliary handle, if

provided, for maximum control over kickback or

torque reaction during start-up. The operator can

control torque reactions or kickback forces, if proper

precautions are taken.

• Never place your hand near the rotating acces-

sory. Accessory may kickback over your hand.

• Do not position your body in the area where

power tool will move if kickback occurs. Kickback

will propel the tool in direction opposite to the wheel’s

movement at the point of snagging.

• Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the ac-

cessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause

loss of control or kickback.

• Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent

kickback and loss of control.

Safety Warnings Specic for Grinding and Abra-

sive Cutting-O󰀨 Operations:

• Use only wheel types that are recommended for

your power tool and the specic guard designed

for the selected wheel. Wheels for which the power

tool was not designed cannot be adequately guarded

and are unsafe.

• The grinding surface of centre depressed wheels

must be mounted below the plane of the guard lip.

An improperly mounted wheel that projects through

the plane of the guard lip cannot be adequately

protected.

• The guard must be securely attached to the power

tool and positioned for maximum safety, so the

least amount of wheel is exposed towards the

operator. The guard helps to protect the operator

from broken wheel fragments, accidental contact

with wheel and sparks that could ignite clothing.

• Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut-o󰀨 wheel. Abrasive cut-o󰀨 wheels are

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Milwaukee 6117-30 Amoladora angular. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Milwaukee. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Milwaukee 6117-30 Amoladora angular en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Milwaukee Amoladoras angulares
Más manuales de Amoladoras angulares

Preguntas frecuentes sobre Milwaukee 6117-30 Amoladora angular

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Milwaukee 2880-22 Amoladora angular

Manual de uso

Milwaukee 2785-21HD Amoladora angular

Manual de uso

Milwaukee 6130-59A Amoladora angular

Manual de uso

Milwaukee 2883-20 Amoladora angular

Manual de uso

Milwaukee 2880-20 Amoladora angular

Manual de uso

Milwaukee 2785-20 Amoladora angular

Manual de uso

Milwaukee 6130-59 Amoladora angular

Manual de uso

Milwaukee 2882-22 Amoladora angular

Categorias relacionadas