Manual de uso Revamp CL-2750 Moldeador

Manual de uso

When you hear a beep and the curling system has come

to a stop, gently lower the autocurler to release the hair. When you reach the middle of

a hair section, repeat the curling process. The end result will have the full-length hair

section beautifully curled from top to boom.

• Aer use, switch off the appliance and allow to cool before storing away. There will be

an audible “beep” to signal the product is turned off.

Follow us on www.revamphair.com for the latest hair tips and advice.

Please note:

• When the product runs out of charge, it will turn itself off with an audible “beep” signal.

• Avoid over-use of styling products as this may deteriorate the coating on the barrel.

• The heated barrel and top end of the appliance get very hot during use. To avoid burns,

keep the barrel away from direct contact with the head and only hold the appliance by

the handle.

• While heating, during use and cooling, place on the REVAMP stand or on a heat resistant

suace. Only hold the product by the cool handle.

• Do not scratch the suace of the curl barrel as this will deteriorate the effectiveness of

the coating.

• The product reaches a very high temperature during operation, please style with

caution when using. Make sure to keep away from the scalp and skin to avoid burns.

CLEANING & MAINTENANCE

• Switch the appliance off and allow to cool fully before cleaning.

• Wipe over all suaces using a so damp cloth. Do not use harsh abrasives or cleaners.

D

BA E

D

logo located on the front of the product are facing you or your friend’s face. Feed the

top of your hair (near the scalp) on the small recess at the front of the product, wrap

the hair pass the barrel and down through the deep apeure at the back, (C), then hold

the appliance around 50-75mm away from your head. (A)

• Choose the direction of the curl by pressing the right or le curling buon (feature

3) as shown in diagram D. Work on one side of the head at a time. When you move on

to the other side, press the opposite direction curling buon so that your curls are

symmetrical (D).

• VERY IMPORTANT - Please do not put your fingers in the deeper apeure at the back of

the product or try to touch the hot barrel.

• Feed the top of your hair (near the scalp) on the small recess at the front of the

product, wrap the hair pass the barrel and down through the deep apeure at the back,

then press and hold the curling buon. The hair will be automatically wrapped around

the heated barrel.

• Keep holding the buon while the hair is wrapped around the barrel and until you hear

the audible beep.

• The curling system stops and a beep is heard aer 15 seconds which is sufficient time

to curl normal hair.

• THE PRODUCT MAY JAM IF TOO MUCH HAIR IS FED AROUND THE BARREL. In this case, the

product will automatically shut off. Simply lower the autocurler veically downwards to

release the hair and turn back on again to continue using.

• Aer hearing the beep, release the curl buon. The

rotating clip will have stopped, and you can lower the

autocurler veically downwards from the hair to release

your curl.

• Caution! When the curling mechanism has stopped, always

lower the autocurler veically downwards to release the curl.

• Repeat for each hair section, allowing each curl time to

cool in between.

• For long hair, curl the hair section as described above.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Revamp CL-2750 Moldeador. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Revamp. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Revamp CL-2750 Moldeador en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Revamp Moldeadores
Más manuales de Moldeadores

Preguntas frecuentes sobre Revamp CL-2750 Moldeador

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Revamp DR-1200 Moldeador

Manual de uso

Revamp BR-2500 Moldeador

Manual de uso

Revamp DR-2000 Moldeador

Manual de uso

Revamp WV-2000 Moldeador

Manual de uso

Revamp TO-1500 Moldeador

Manual de uso

Revamp CL-2000 Moldeador

Manual de uso

Revamp DR-1150 Moldeador

Manual de uso

Revamp CL-1850 Moldeador

Categorias relacionadas