Manual de uso RIDGID R41422 Sierra de corte

Manual de uso

3 - English

SPECIFIC SAFETY RULES

 FIRMLY CLAMP OR BOLT your tool to a workbench or

table at approximately hip height.

USE ONLY CORRECT WHEELS. Do not use wheels with

incorrect size holes. Never use wheel washers or wheel

screws that are defective or incorrect. The maximum

wheel capacity of your cut-off machine is 14 in.

DO NOT REMOVE THE MACHINE'S WHEEL GUARDS.

Never operate the machine with any guard or cover

removed. Make sure all guards are operating properly

before each use.

KEEP HANDS AWAY FROM CUTTING AREA. Keep

hands away from wheel. Do not reach underneath work

or around or under the wheel while the wheel is rotating.

Do not attempt to remove cut material while wheel is

moving.

ALWAYS SUPPORT LONG MATERIAL. To minimize

risk of tipping machine, always support long material.

BEFORE MAKING A CUT, BE SURE ALL

ADJUSTMENTS ARE SECURE.

ALWAYS USE THE VISE CLAMP to secure the material.

NEVER cut more than one piece of material at a time.

DO NOT STACK more than one piece of material on the

machine base at a time.

NEVER PERFORM ANY OPERATION “FREEHAND”.

Always secure the material to be cut in the vise.

NEVER hand hold a piece of material. Material will become

very hot while being cut.

NEVER reach behind, under, or within three inches of the

wheel and its cutting path with your hands and fingers

for any reason.

NEVER reach to pick up a piece of material, a piece of

scrap, or anything else that is in or near the cutting path

of the wheel.

AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause your hand

to move into the wheel. ALWAYS make sure you have

good balance.

NEVER stand or have any part of your body in line with

the path of the wheel.

ALWAYS release the power switch and allow the wheel

to stop rotating before raising wheel guard or removing

material.

GENERAL SAFETY RULES

 INSPECT TOOL CORDS PERIODICALLY. If damaged,

have repaired by a qualified service technician at an

authorized service facility. The conductor with insulation

having an outer surface that is green with or without yellow

stripes is the equipment-grounding conductor. If repair

or replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor to a

live terminal. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating wheel.

 INSPECT EXTENSION CORDS PERIODICALLY and

replace if damaged.

 POLARIZED PLUGS. To reduce the risk of electric shock,

this tool has a polarized plug (one blade is wider than the

other). This plug will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet, reverse the plug.

If it still does not fit, contact a qualified electrician to install

the proper outlet. Do not change the plug in any way.

 KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND

GREASE. Always use a clean cloth when cleaning. Never

use brake fluids, gasoline, petroleum-based products,

or any solvents to clean tool.

 STAY ALERT AND EXERCISE CONTROL. Watch what

you are doing and use common sense. Do not operate

tool when you are tired. Do not rush.

 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT

ON AND OFF. Have defective switches replaced by an

authorized service center.

 NEVER TOUCH WHEEL or other moving parts during

use.

NEVER START THE CUT-OFF MACHINE WHEN THE

WHEEL IS IN CONTACT WITH THE MATERIAL.

 DO NOT OPERATE A TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR ANY

MEDICATION.

 WHEN SERVICING use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

 USE ONLY RECOMMENDED ACCESSORIES listed

in this manual or addendums. Use of accessories that

are not listed may cause the risk of personal injury.

Instructions for safe use of accessories are included

with the accessory.

 DOUBLE CHECK ALL SETUPS. Make sure wheel is tight

and not making contact with tool or workpiece before

connecting to power supply.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus RIDGID R41422 Sierra de corte. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con RIDGID. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu RIDGID R41422 Sierra de corte en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para RIDGID Sierras de corte
Más manuales de Sierras de corte

Preguntas frecuentes sobre RIDGID R41422 Sierra de corte

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Bosch GCO 240 Sierra de corte

Manual de uso

Siefken CD3525 Sierra de corte

Manual de uso

Stayer TD 355 B Sierra de corte

Manual de uso

Scheppach MT150 Sierra de corte

Manual de uso

Bosch GCO 200 Sierra de corte

Manual de uso

Elite CS1424 Sierra de corte

Manual de uso

Einhell TC-MC 355 Sierra de corte

Manual de uso

DeWalt D28730 Sierra de corte

Categorias relacionadas