Manual de uso Ruwido Easytip S2 Control remoto

Manual de uso

Easy programming for the control of your TUNER

(RADIO)

To programme the remote control to operate your TUNER, proceed as

described for the CD PLAYER but using the key instead of the CD key.

Please ensure that you refer to the codes listed under the TUNER section and

not the CD PLAYER section.

Easy programming for the control of your TAPE

RECORDER (TAPE DECK)

To programme the remote control to operate your TAPE RECORDER, proceed

as described for the CD PLAYER but using the key instead of the CD key.

Please ensure that you refer to the codes listed under the TAPE section and not

the CD PLAYER section.

Easy programming for the control of your AMPLIFIER

To programme the remote control to operate your AMPLIFIER, proceed as

described for the CD PLAYER. Complete steps 1 to 10, using the key on

your remote control. Please ensure that you refer to the codes listed under the

AMPLIFIER section and not CD PLAYER section.

Code scan

If programming using the codes in the enclosed list failed to work then you

must next try the automatic code scan.

A. Ensure that the remote control is equipped with 2 new batteries (see step

one of easy programming procedure).

B. Switch on your TV SET. When using the automatic scan function for the

VCR, DVD, CD or TAPE, switch on your device, insert a video tape, DVD,

CD or tape cassette and put the unit into ‘Play mode’ i.e, the VCR tape etc

is running.

C. Press the key of your remote control for approx. 4 seconds until the

LED flashes twice.

D. After seeing the 2 flashes and within 5 seconds, enter the code .

After entering the code the LED will flash twice indicating that the code has

been accepted

E. Press and hold the key until your TV switches off. Please note that this

process might take up to 15 minutes. During the automatic scanning you

can remove your finger or change hands provided it is replaced within 8

seconds. If left off of the key for more than 8 seconds then the remote will

revert back to its normal mode. If your TV switches into Stand-By mode

during the automatic process then immediately remove your finger from the

key and then press and release the key until the LED flashes

twice, this will then store the code that the remote has found

F. In some cases during the automatic scanning search the remote control

might find several codes that appear to operate your TV etc, however, if

some of the buttons fail to work properly then it’s possible the remote has

found a partially compatible code. In such cases you will need to restart the

automatic scanning process (steps B. to F.) until a better code is found.

Please note that once the automatic process is restarted, the remote

continues from the last stored code and not at the beginning of code

database.

• To complete a code scan for the VCR, DVD, CD or TAPE, follow the

procedure above but use the key and not the key

• To complete a code scan for the TUNER, follow the procedure above but

use the key

2

TV

1

0

0

TV

AMP

TAPE

TUNER

3

UNIVERSAL REMOTE CONTROL

Thank you for purchasing this universal remote control. Before using the

remote you will need to insert 2 type "AAA" batteries (not included) in the

battery compartment ensuring that you follow the polarity shown on the inside.

You can now use your remote control to operate up to 9 different devices

(depending on the model) including a TV, video recorder, DVD player, satellite or

cable receiver, CD player, tuner (radio), tape recorder and amplifier. If your

remote control is equipped with an AUX key (not standard on all models) then

you can also use it to control a second TV set, video recorded, satellite receiver

and/or cable box, CD player, tuner, tape recorder or amplifier!

Easy programming for the control of your TV SET

1. Insert 2 new 1.5V alkaline batteries of type "AAA/LR03". Observe battery

polarity as indicated in the battery compartment.

2. Switch on your TV SET.

3. In the enclosed code list, find your TV brand or manufacturer (e.g. Sony).

4. Beside the manufacturer's name, you will find one or more 3-digit codes.

These codes must be entered into the remote to enable it to work with your

particular TV set.

5. Press the key on the remote control for approximately 4 seconds until

the LED flashes twice.

6. After seeing the 2 flashes and within 5 seconds, enter the 3-digit numerical

code from the list.

7. After entering the code the LED will flash twice indicating that the code has

been accepted.

8. Point the remote control towards your TV and press the key. If your TV

does not respond by going into Stand-By mode then repeat steps 3 to 8

and enter the next code in the list.

9. If your TV goes into Stand-By mode when the key pressed then your

remote control has found a compatible code. Next test all of the other

function buttons. If certain functions are not working correctly then restart

the process moving onto the next code number as this may well improve

the situation.

10. If the codes in the list fail to operate your TV then next move onto the

automatic code scan function (see below).

Easy programming for the control of your VIDEO

RECORDER

To programme the remote control to operate your VIDEO RECORDER, proceed

as described above for the television set. Complete steps 1 to 10 using the

key on your remote control. Please ensure that you refer to the codes

listed under the VIDEO RECORDER section and not the TV section.

Easy programming for the control of your SATELLITE

RECEIVER

To programme the remote control to operate your SATELLITE RECEIVER or

CABLE BOX, proceed as described for the television set. Complete steps 1 to

10 using the key on your remote control. Please ensure that you refer to

the codes listed under the SATELLITE section and not the TV section.

Easy programming for the control of your DVD PLAYER

To programme the remote control to operate your DVD PLAYER, proceed as

described for the television set. Complete steps 1 to 10 using the key on

your remote control. Please ensure that you refer to the codes listed under the

DVD section and not the TV section.

Easy programming for the control of your CD PLAYER

To programme the remote control to operate your CD PLAYER, proceed as

described for the television set. Complete steps 1 to 10 except you must first

press and release the key followed by holding down the key. Please

ensure that you refer to the codes listed under the CD section and not the TV

section.

CD

SHIFT

DVD

SAT

VCR

TV

2

USER MANUAL

GB

USER MANUAL

GB

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Ruwido Easytip S2 Control remoto. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Ruwido. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Ruwido Easytip S2 Control remoto en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Ruwido Controles remotos
Más manuales de Controles remotos

Preguntas frecuentes sobre Ruwido Easytip S2 Control remoto

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Ruwido Easytip S3 Control remoto

Manual de uso

Ruwido Digital 3 Control remoto

Manual de uso

Ruwido Easytip S5 Control remoto

Manual de uso

Ruwido Easytip S9 Control remoto

Manual de uso

Ruwido Easytip Z3 Control remoto

Manual de uso

Ruwido M_4 Control remoto

Manual de uso

Ruwido Easytip S4 Control remoto

Manual de uso

Ruwido Easytip S7 Control remoto

Categorias relacionadas