Manual de uso Ryobi ERT1400RV Fresadora de superficie

Manual de uso

6

English

GB

FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR

FINE HEIGHT ADJUSTER

It is used to precisely control the depth of the cutter.

1. To use the  ne height adjuster, ensure that the plunge

lock is released.

2. Rotate the knob clockwise to raise the cutter,

anticlockwise to lower the cutter.

3. When the desired position is reached, re-engage the

plunge lock before use.

FINE HEIGHT ADJUSTER QUICK RELEASE BUTTON

This disengages the  ne height adjuster allowing large

adjustments of plunge depth to be quickly made.

1. To make large adjustments to cutter height, ensure

that the plunge lock is released.

2. Press the quick release button whilst plunging the

router to the required height.

3. Release the button, check the height, make  ne

adjustments if necessary with the  ne height adjuster,

then re-engage the plunge lock before use.

DEPTH OF CUT

As previously mentioned, the depth of cut is important

because it affects the rate of feed that, in turn, affects the

quality of the cut (and, also, the possibility of damage to

your router motor and bit). A deep cut requires a slower

feed than a shallow one, and a too deep cut will cause you

to slow the feed so much that the bit is no longer cutting,

it is scraping, instead.

Making a deep cut is never advisable. The smaller bits are

easily broken off when subjected to too much side thrust.

A large enough bit may not be broken, but if the cut is too

deep, a rough cut will result, and it may be very dif cult to

guide and control the bit as desired. For these reasons, we

recommend that you do not exceed 1/8 in (3.2 mm) depth

of cut in a single pass, regardless of the bit size or the

softness or condition of the workpiece.

To make deeper cuts it is therefore necessary to make as

many successive passes as required, lowering the bit 1/8

in (3.2 mm) for each new pass. In order to save time, do all

the cutting necessary at one depth setting, before lowering

the bit for the next pass. This will also assure a uniform

depth when the  nal pass is completed.

LIVE TOOL INDICATOR

This tool features a live tool indicator which illuminates as

soon as the tool is connected to the supply. This warns the

user that the tool is connected and will operate when the

switch is pressed.

MAINTENANCE

WARNING

When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

GENERAL

Avoid using solvents when cleaning plastic parts.

Most plastics are susceptible to damage from various

types of commercial solvents. Use clean cloths to remove

dirt, carbon dust, etc.

WARNING

Do not at any time let brake  uids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. They contain chemicals that can

damage, weaken or destroy plastic.

Electric tools used on  berglass material, wallboard,

spackling compounds, or plaster are subject to accelerated

wear and possible premature failure because the  berglass

chips and grindings are highly abrasive to bearings,

brushes, commutators, etc.. Consequently, we do not

recommended that this tool be used for extended work on

these types of materials. If, however, you do work with any

of these materials, it is extremely important that you clean

the tool frequently by blowing it with an air jet.

WARNING

Always wear safety goggles or safety glasses with side

shields during power tool operation or when blowing

dust. If operation is dusty, also wear a dust mask.

LUBRICATION

All of the bearings in this tool are lubricated with a

suf cient amount of high grade lubricant for the life of

the unit under normal operating conditions. Therefore, no

further lubrication is required.

CUTTERS

Get faster and more accurate cutting results by keeping

cutters clean and sharp. Remove all accumulated pitch

and gum from cutters after each use.

When sharpening cutters, sharpen only the inside of the

cutting edge. Never grind the outside diameter. Be sure

when sharpening the end of a cutter to grind the clearance

angle the same as originally ground.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Ryobi ERT1400RV Fresadora de superficie. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Ryobi. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Ryobi ERT1400RV Fresadora de superficie en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Ryobi Fresadoras de superficie
Más manuales de Fresadoras de superficie

Preguntas frecuentes sobre Ryobi ERT1400RV Fresadora de superficie

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Parkside IAN 100129 Fresadora de superficie

Manual de uso

DeWalt DW618M Fresadora de superficie

Manual de uso

Skil 1840 AD Fresadora de superficie

Manual de uso

DeWalt DWE625 Fresadora de superficie

Manual de uso

Makita RP1111C Fresadora de superficie

Manual de uso

Bosch GKF 12V-8 Fresadora de superficie

Manual de uso

Bosch POF 400 A Fresadora de superficie

Manual de uso

FERM PRM1006 Fresadora de superficie

Categorias relacionadas