Manual de uso Ryobi RTS18C-0 Sierra circular

Manual de uso

reactions or kickback forces, if proper precautions are

taken.

■ Never place your hand near the rotating

accessory. Accessory may kickback over your hand.

■ Do not position your body in line with the rotating

wheel. Kickback will propel the tool in direction

opposite to the wheel’s movement at the point of

snagging.

■ Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have

a tendency to snag the rotating accessory and cause

loss of control or kickback.

■ Do not attach a saw chain, woodcarving blade,

segmented diamond wheel with a peripheral gap

greater than 10 mm or toothed saw blade. Such

blades create frequent kickback and loss of control.

■ Do not “jam” the wheel or apply excessive pressure.

Do not attempt to make an excessive depth of cut.

Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut

and the possibility of kickback or wheel breakage.

■ When wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold

the power tool motionless until the wheel comes to

a complete stop. Never attempt to remove the wheel

from the cut while the wheel is in motion otherwise

kickback may occur. Investigate and take corrective

action to eliminate the cause of wheel binding.

■ Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully re-enter

the cut. The wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

■ Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

■ Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

ADDITIONAL SAFETY WARNINGS

■ Clamp workpiece with a clamping device. Unclamped

workpieces can cause severe injury and damage.

■ Injuries may be caused, or aggravated, by prolonged

use of a tool. When using any tool for prolonged periods,

ensure you take regular breaks.

■ Do not switch on the product again after it has stalled.

Switching it on again can cause a kickback with high

reaction force. Determine why the product has stalled

and rectify it, paying heed to the safety instructions.

■ Ambient temperature range for tool during operation is

between 0 ˚C and 40 ˚C.

■ Ambient temperature range for tool storage is between

0 ˚C and 40 ˚C.

■ The recommended ambient temperature range for the

charging system during charging is between 10 ˚C and

38 ˚C.

ADDITIONAL BATTERY SAFETY WARNINGS

■ To reduce the risk of fire, personal injury, and product

damage due to a short circuit, never immerse the tool,

battery pack, or charger in fluid or allow a fluid to flow

inside them. Corrosive or conductive fluids, such as

seawater, certain industrial chemicals, and bleach or

bleach-containing products, etc., can cause a short

circuit.

■ Ambient temperature range for battery during use is

between 0 °C and 40 °C.

■ Ambient temperature range for battery storage is

between 0 °C and 20 °C.

TRANSPORTING LITHIUM BATTERIES

Transport the battery in accordance with local and national

provisions and regulations.

Follow all special requirements on packaging and labelling

when transporting batteries by a third party. Ensure that

no batteries can come in contact with other batteries

or conductive materials while in transport by protecting

exposed connectors with insulating, non-conductive caps or

tape. Do not transport batteries that are cracked or leaking.

Check with the forwarding company for further advice.

KNOW YOUR PRODUCT

See page 71.

1. Battery port

2. Water bottle

3. Handle, insulated gripping surface

4. Lock-on button

5. Switch trigger

6. Water bottle connector

7. Dust port

8. Water bottle release button

9. Depth of cut adjustment lever

10. Water flow adjustment knob

11. Cutting wheel

12. Inner wheel washer

13. Outer wheel washer

14. Wheel screw

15. LED light

16. Spindle lock

17. Bevel lock knob

18. Edge guide

19. Operator’s manual

20. Battery pack

21. Charger

MAINTENANCE

■ The product should never be connected to a power

supply when assembling parts, making adjustments,

cleaning, performing maintenance, or when the product

is not in use. Disconnecting the product from the power

supply will prevent accidental starting that could cause

serious injury.

■ When servicing, use only original manufacturer’s

replacement parts, accessories, and attachments. Use

of any other parts may create a hazard or cause product

damage.

■ Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to various types of commercial

solvents and may be damaged by their use. Use clean

cloths to remove dirt, carbon dust, etc.

4

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Ryobi RTS18C-0 Sierra circular. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Ryobi. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Ryobi RTS18C-0 Sierra circular en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Ryobi Sierras circular
Más manuales de Sierras circular

Preguntas frecuentes sobre Ryobi RTS18C-0 Sierra circular

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Ryobi R18CSP-0 Sierra circular

Manual de uso

Ryobi RWS1400 Sierra circular

Manual de uso

Ryobi LSC-180 Sierra circular

Manual de uso

Ryobi LTS180M Sierra circular

Manual de uso

Ryobi RWS1250 Sierra circular

Manual de uso

Ryobi RWS1600 Sierra circular

Manual de uso

Ryobi EWS1266 Sierra circular

Manual de uso

Ryobi RCT18C-0 Sierra circular

Categorias relacionadas