Manual de uso Stickfast GX80 Pistola para pegar

Manual de uso

EDITION FEB 2017

Warning

When using this hot melt glue gun always follow basic safety

p

recautions. Wear protective gloves, long sleeved clothing and

safety glasses, to reduce the possibility of accidental injury.

Read all the safety instructions.

Read all the safety instructions

Safety instructions

X

tegra

®

S

tickfast™ 240v model glue guns are recommended for

i

ndoor use only and should not be used in wet or damp conditions.

Your work area should be well lit. The operating temperature of

the guns is between 120˚C- 230˚C. Do not touch the heated nozzle

or molten adhesive with bare skin. Protective gloves should al-

ways be worn. Careless handling can cause skin burns.

If molten adhesive comes into contact with the skin, immerse the

a

ected area immediately in cold water. Seek medical advice if

necessary, do not remove the adhesive from the skin.

Disconnect the electrical power supply to the glue gun after use,

before servicing and when changing accessories.

Allow time for the gun nozzle to cool down suciently before

handling. Never immerse the gun or its nozzle in water or other

liquids to accelerate the cooling process. Do not leave the gun

unattended while plugged in or still hot. If it is not to be reused

within one hour, disconnect the electrical power supply.

It is normal for this device to become warm during use and does

not indicate a problem.

Operation (All glue guns except SL150B)

> Use only recommended Stickfast™ adhesives in this glue

gun. The use of other manufacturers’ products will

invalidate the warranty.

> Before using the gun for the first time check carefully for

signs of external damage. If any damage has occurred in

transit do not use it; return it to your supplier immediately.

> Attach the enclosed metal glue gun stand, locating the

hooks on its legs in the holes on either side of the gun

casing.

> Insert a Stickfast™ glue stick into the rear of the tool and

push the stick forward until slight resistance is felt.

> Plug the gun into a 240V AC outlet and allow the tool to

heat up for approximately 3-5 minutes. When the gun is

fully heated squeeze the trigger until the molten adhesive

begins to flow from the nozzle.

> Release the trigger to stop the flow. Do not apply

excessive pressure to the trigger as this can cause

blockages. If a blockage occurs, leave the gun to stand for

a minute, then gently try again.

> The first time a glue gun is used it may smoke from the

nozzle. This is normal and will stop as soon as glue has

filled the melt chamber.

> Apply the adhesive wherever it is required. When adhesive

can no longer be extruded from the tool, insert a new glue

stick into the rear of the tool to resume operation.

Operation (SL150B cordless model)

> Use only recommended Stickfast™ adhesives in this glue

g

un. The use of other manufacturers’ products will

invalidate the warranty.

> Before using the gun for the first time check carefully for

s

igns of external damage. If any damage has occurred in

t

ransit do not use it; return it to your supplier immediately.

> Turn on to heat the gun; a red light is illuminated to

indicate power supply.

>

Insert a Stickfast™ glue stick into the rear of the tool and

push the stick forward until slight resistance is felt.

> Pre-heat time is about 5-8 minutes before the gun is

ready to use. When the gun is fully heated squeeze the

trigger until the molten adhesive begins to flow from

t

he nozzle.

> Release the trigger to stop the flow. Do not apply

excessive pressure to the trigger as this can cause

blockages. If a blockage occurs, leave the gun to stand

for a minute, then gently try again.

> The first time a glue gun is used it may smoke from the

nozzle. This is normal and will stop as soon as glue has

filled the melt chamber.

> Apply the adhesive wherever it is required. When

adhesive can no longer be extruded from the tool, insert

a new glue stick into the rear of the tool to resume

operation.

> The indicator light flashes for two minutes before the

battery is exhausted and the heater turns o

automatically. Replace with a fully charged battery to

resume operation.

> Operating time is about 60 minutes (based on our

suggested battery capacity, 1.3Ah 36V)

> To release the battery, press the battery lock button. To

replace the battery, push battery in to the base of the gun

until the battery locks in place.

> Warning: Please take extra care with the heated nozzle;

the SL150B is a cordless model and it is easy to forget

that the gun may still be hot.

4

STICKFAST Operating Instructions

G

B

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Stickfast GX80 Pistola para pegar. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Stickfast. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Stickfast GX80 Pistola para pegar en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Stickfast Pistolas para pegar
Más manuales de Pistolas para pegar

Preguntas frecuentes sobre Stickfast GX80 Pistola para pegar

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Stickfast GX120 Pistola para pegar

Manual de uso

Stickfast SL120 Pistola para pegar

Manual de uso

Stickfast GX600 Pistola para pegar

Manual de uso

Stickfast GX80LT Pistola para pegar

Manual de uso

Stickfast GX300 Pistola para pegar

Manual de uso

Stickfast GX600A Pistola para pegar

Manual de uso

Stickfast SL150B Pistola para pegar

Manual de uso

Stickfast SL300 Pistola para pegar

Categorias relacionadas