Manual de uso Vivanco UR 850 LCD Control remoto

Manual de uso

UR 850 LCD Universal Controller

Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, e-Mail: [email protected] 1

(GB) Operating Instructions

Vivanco UR 850 LCD remote control for

practically all TV, audio, video and other

infrared-controllable devices

Inserting the batteries

Open the battery compartment on the back of the

device, push the flap down lightly and insert 2 AA

alkaline batteries. Make sure that the polarity on the

batteries and in the battery compartment correspond

(thick spring = cell at bottom = -) and then close the

lid carefully. – Use undamaged batteries only.

Adapting to devices

In order to control your devices you must adapt or

set the remote control to them. There are two ways

of doing so: direct control code entry or code

search.

If the UR 850 LCD does not understand you it

displays ERROR and you can then repeat the entry.

Direct control code entry

Example: setting the remote control for a Philips TV

set:

1. Switch on your device, e.g. the TV, set to any

station.

2. To prepare code entry, briefly press the SET

button in the bottom right corner of the keypad, then

the required device button, e.g. TV. A brand and a

code number appear, see diagram.

– You cannot enter

a new code if you have activated the code entry lock.

3. Select the brand of your device, in this

example Philips, with  or . The first available

code in the device list is displayed.

4. Press a few buttons to determine whether you

have found a suitable code. When the code

corresponds to your device, press OK and the

setting for this device is completed.

5. If the code you have found does work at all or

not properly, try another code by selecting the next

code for the brand using the  or  button, then

test the code as described above under 4. and, if

successful, confirm with OK.

6. To set the remote control for other devices,

proceed in the same way. Instead of the TV device

button, press another button, e.g. VCR, CBL/SAT

(DVB-T, DECODER), DVD, TUNER, TAPE, CD,

AUX).

-Before setting a code and performing the subsequent test

for recording or playback devices, please insert a medium

(tape, CD, cassette, DVD, etc.).- You can interrupt code

entry at any time by pressing EXIT.

Code search

If the brand of your appliance is not in the list or

none of the codes given fits, we recommend the

automatic code search.

Your remote control finds the correct control settings

almost automatically in a few seconds:

1. Switch on the device to be controlled. For

example, a program number appears in the display

of your satellite receiver.

2. To start the code search, press and hold the

SET button for approx. 3 seconds. CODE SETUP

appears in the display. Confirm this function by

pressing OK.

3. DEV SEARCH then appears in the display.

Confirm this function by pressing OK.

– If DEV

SEARCH does not appear you can set the function with the

 or button.

4. Press the device button of the device to be

controlled, e.g. DVD and confirm the function by

pressing OK.

5. Then point the remote control at the device to

be controlled while the remote control emits a

different ON/OFF signal every 2 seconds. The

respective code number is shown in the display.

6. When your device reacts, press a few buttons

to determine whether you have found a suitable

code. If the code corresponds to your device, press

OK twice. SUCCESS appears in the display, then

you press the device button, e.g. DVD, to confirm

the entry. The setting for this device is now

completed.

7. If the code you have found does work at all or

not properly, press EXIT and DEV SEARCH

appears again. Then proceed again as described

under 3.

Please note: - You can reverse the search direction with the

 or  button if you have reacted too slowly to a response

from the device. – The Menu buttons cannot by used for

testing. - Before setting a code and performing the

subsequent test for recording or playback devices, please

insert a medium (tape, CD, cassette, DVD, etc.).- You can

interrupt code entry at any time by pressing EXIT.

Other settings

Setting the time

1 Press and hold SET for 3 seconds, then set

CONFIGURE with the  or  button. Confirm this

function by pressing OK.

2 TIME SETUP appears in the display. Confirm

this function by pressing OK.

3 Enter the time using the number buttons and

confirm with the OK button. Then press EXIT

several times to quit the setting mode.

Set priority volume control

With this function you can determine a device

exclusively for volume control, e.g. your audio

amplifier. Then the buttons VOL +, VOL – and

always control the amplifier, regardless of which

device you are controlling.

1 Press and hold SET for 3 seconds, then set

CONFIGURE with the  or  button. Confirm this

function by pressing OK

2 TIME SETUP appears in the display. Set VOL

LOCK with the  or  button. Confirm this function

by pressing OK.

3 Select the device button, e.g. AUX for the

amplifier and set priority=ON using the  or 

button. Confirm this function by pressing OK.

4 Then press EXIT several times to quit the

setting mode.

- You can cancel the priority setting using the same

procedure. Instead of ON, set OFF for all devices.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Vivanco UR 850 LCD Control remoto. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Vivanco. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Vivanco UR 850 LCD Control remoto en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Vivanco Controles remotos
Más manuales de Controles remotos

Preguntas frecuentes sobre Vivanco UR 850 LCD Control remoto

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Vivanco UR 81 Control remoto

Manual de uso

Vivanco Viv.Control 3 Control remoto

Manual de uso

Vivanco UR 82 SE Control remoto

Manual de uso

Vivanco Viv.Control 5 Control remoto

Manual de uso

Vivanco UR 03 UF Control remoto

Manual de uso

Vivanco UR Z2 Control remoto

Manual de uso

Vivanco UR 40 USB Control remoto

Manual de uso

Vivanco UR 100 LCD Control remoto

Categorias relacionadas