Manual de uso Whirlpool FFT M11 82 SPT R Secadora

Manual de uso

THANK YOU FOR BUYING AN INDESIT PRODUCT.

In order to receive a more complete assistance,

please register your product on

www.indesit.eu/register

Policies, standard documentation, ordering of spare parts and additional product information can be found by:

• Using QR code in your appliance

• Visiting our website docs.indesit.eu and parts-selfservice.europeanappliances.com

• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales

Service, please state the codes provided on your product's identi cation plate.

EN

Before using the appliance carefully

read the Safety Instruction.

PLEASE SCAN THE QR CODE ON YOUR APPLIANCE IN ORDER TO REACH MORE INFORMATION.

Quick guide

Before using the appliance carefully

read the Safety Instruction.

Power consumption

o-mode (Po) - Watts 0.42

left-on mode (Pl) - Watts 2.00

Programs Kg kWh Minutes

Eco *

8 1.95 194

Eco

4 1.06 135

Synthetics 4 0.73 95

*This is the reference programme for the energy label and suitable to

dry normal wet cotton laundry. This is the most ecient programme

in terms of energy consumption for drying wet cotton laundry

(Standard/Default starting conguration).

Cleaning the tumble dryer

• The external metal, plastic and rubber parts can be cleaned

with a damp cloth.

• Clean the front air intake grille regularly (every 6 months) with

a vacuum cleaner to remove any lint, u or dust deposits.

Furthermore, remove any lint deposits from the lters area,

using a vacuum cleaner every so often.

• Do not use solvents or abrasives.

AB

1

4

2

3

C

C1 C2 C3

C4

C5

C6

CLEANING AND MAINTENANCE

WARNING: unplug the dryer during the cleaning and

maintenance procedures.

Emptying the water tank after each cycle (see Fig. A).

Pull the container out of the dryer and empty it into a sink or other

suitable drain, then place it back properly. Do not use the dryer

without having inserted the container back in place.

Cleaning the lters

Take out the lters and clean them by removing the lint from their

surfaces with your hand or a cloth or using a vacuum cleaner, then

put them back in place. The lint should be thrown in the garbage

bin and not washed through the drain in order to avoid spreading

microplastics in the used water system.

Do not use the dryer without having reinserted the lter in place.

Cleaning the door lter after each cycle (see Fig. B).

Remove the door lter as described below:

1. Open the door and pull the lter upwards.

2. Open the lter and remove the lint from all its parts. Replace

the lter correctly making sure it is fully seated.

Cleaning the bottom lter when the relevant indicator

turns on (see Fig. C).

NOTE: however, it is advisable to clean this lter after each cycle

to optimise drying performance.

Remove the bottom lter as described below:

C1. Open the bottom cover; take the handle and pull the lter out.

C2. Open the rear side of the lter and remove the lint from the

inner surface of the mesh.

C3/C4. Check the bottom lter chamber every month. If you

see residual lint accumulated on the metal ns, clean it with a

vacuum cleaner, using a nozzle with a brush.

It's crucial to do vertical movements, you may destroy the

component if you try to clean it in horizontal direction. Avoid the

direct contact of the hand with the ns - risk of cut.

C5. Close the rear side of the lter and place it back by checking it

is perfectly integrated into its seat, then lower the lter handle.

C6. Close the bottom cover.

Make sure the air intake is free.

The lters are essential parts for drying. They are intended

to collect the lint formed during the drying process. In case

of clogged lters, the air ow inside the dryer would be

seriously aected: the drying times would be longer, the

energy consumption would increase and the dryer could be

damaged. If these procedures are not carried out properly,

the dryer may not start.

PRODUCT DESCRIPTION

1. Water Tank

2. Air Intake

3. Bottom lter

4. Door lter

NOTE: After cleaning the lters the relevant indicator remains

on; this is normal, it will disappear when you start a new drying

cycle.

TRANSPORT AND HANDLING

Never lift the dryer by holding it at the worktop.

1. Unplug the dryer.

2. Remove the water from the water tank completely.

3. Make sure that door and water tank are properly closed.

4. If the drain hose is connected to your drainage system,

re-connect it to the back of the dryer (see "Installation" section

in the Safety Instruction guide).

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Whirlpool FFT M11 82 SPT R Secadora. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Whirlpool. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Whirlpool FFT M11 82 SPT R Secadora en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Whirlpool Secadoras
Más manuales de Secadoras

Preguntas frecuentes sobre Whirlpool FFT M11 82 SPT R Secadora

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Whirlpool C WSD 74M WBS ES Secadora

Manual de uso

Whirlpool FFT M11 82 EE R Secadora

Manual de uso

Whirlpool AWZ 541 Secadora

Manual de uso

Whirlpool FT M22 9X2Y EU Secadora

Manual de uso

Whirlpool 3LWED5500YW Secadora

Manual de uso

Whirlpool WTD 950B BK EU Secadora

Manual de uso

Whirlpool AWZ 3669 WP Secadora

Manual de uso

Whirlpool WGD8127LW Secadora

Categorias relacionadas