Manual de uso Whirlpool UDT518SAHP Lavavajillas

Manual de uso

3

Connected Appliance Regulatory Notices

Federal Communications Commission (FCC)

Compliance Notice

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the

following measures:

■ Reorient or relocate the receiving antenna.

■ Increase the separation between the equipment and receiver.

■ Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

■ Consult the dealer or an experienced radio/TV technician for

help. This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

Changes or modications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

RF Exposure Information

To comply with FCC/IC RF exposure requirements for mobile

transmitting devices, this transmitter should only be used or

installed at locations where there is at least 20 cm separation

distance between the antenna and all persons.

To comply with FCC/IC RF exposure limits for general

population/uncontrolled exposure, the antenna(s) used for this

transmitter must be installed to provide a separation distance of

at least 20 cm from all persons and must not be co-located or

operating in conjunction with any other antenna or transmitter.

Industry Canada (IC) Compliance Notice

This Device complies with Industry Canada License-exempt RSS

standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference,

2. This device must accept any interference, including

interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may

only operate using an antenna of a type and maximum (or lesser)

gain approved for the transmitter by Industry Canada. To reduce

potential radio interference to other users, the antenna type and its

gain should be so chosen that the equivalent isotropically radiated

power (e.i.r.p.) is not more than that necessary for successful

communication.

The radio transmitters IC: 10248A-WICHAM01 and

10248A-FLDAAM01 have been approved by Industry Canada to

operate with the antenna types listed below with the maximum

permissible gain and required antenna impedance for each

antenna type indicated. Antenna types not included in this list,

having a gain greater than the maximum gain indicated for that

type, are strictly prohibited for use with this device.

Antenna Type Maximum Permissible

Antenna Gain (dBi)

Required

Impendance

(OHM)

Slot 1.2 50

Monopole

(WICHAM01 only)

0.5 50

Dipole 3.0 50

F 1.60 50

Planar F 4.2 50

To comply with FCC and Industry Canada RF radiation exposure

limits for general population, the antenna(s) used for this

transmitter must be installed such that a minimum separation

distance of 20 cm is maintained between the radiator (antenna)

and all persons at all times and must not be co-located or

operating in conjunction with any other antenna or transmitter.

Le présent appareil est conforme aux CNR d’Industrie Canada

applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes :

(1) l’appareil ne doit pas produire de brouillage, et

(2) l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement. Conformément à la réglementation

d’Industrie Canada, le présent émetteur radio peut fonctionner avec

une antenne d’un type et d’un gain maximal (ou inférieur) approuvé

pour l’émetteur par Industrie Canada. Dans le but de réduire

les risques de brouillage radioélectrique à l’intention des autres

utilisateurs, il faut choisir le type d’antenne et son gain de sorte que

la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse

pas l’intensité nécessaire à l’établissement d’une communication

satisfaisante. Le émetteurs radio IC : 10248A-WICHAM01et

10248A-FLDAAM01ont été approuvés par Industrie Canadapour

fonctionner avec les types d’antenne énumérés ci-dessous et ayant

un gain admissible maximal et l’impédance requise pour chaque

type d’antenne. Les types d’antenne non inclus dans cette liste, ou

dont le gain est supérieur au gain maximal indiqué, sont strictement

interdits pour l’exploitation de l’émetteur.

Type d’antenne Gain

admissiblemaximal

d’antenne (dBi)

L’impédance

requise (OHM)

À fentes 1.2 50

Monopôle (WICHAM01

seulement)

0.5 50

Dipole 3.0 50

F 1.60 50

Planaire F 4.2 50

Pour satisfaire aux exigences de la FCC et IC d’exposition aux

radiofréquences, une distance de séparation de 20 cm ou plus

doit être maintenue entre cet appareil et des personnes lors de

fonctionnement du dispositif. Pour assurer la conformité des

opérations au plus près que cette distance n’est pas recommandée.

L’antenne utilisée pour ce transmetteur ne doit pas être co-localisés

en conjonction avec toute autre antenne ou transmetteur.

OEM Responsibilities to comply with FCC and Industry Canada

Regulations

The WICHAM01/FLDAAM01 Modules have been certied for

integration into products only by OEM integrators under the

following conditions:

1. The antenna(s) must be installed such that a minimum

separation distance of 20 cm is maintained between the

radiator (antenna) and all persons at all times.

2. The transmitter module must not be co-located or operating in

conjunction with any other antenna or transmitter.

As long as the two conditions above are met, further transmitter

testing will not be required. However, the OEM integrator is

still responsible for testing their end-product for any additional

compliance requirements required with this module installed (for

example, digital device emissions, PC peripheral requirements,

etc.).

IMPORTANT NOTE: In the event that these conditions cannot

be met (for certain congurations or co-location with another

transmitter), then the FCC and Industry Canada authorizations

are no longer considered valid and the FCC ID and IC

Certication Number cannot be used on the nal product. In

these circumstances, the OEM integrator will be responsible

for re-evaluating the end product (including the transmitter) and

obtaining a separate FCC and Industry Canada authorization.

End Product Labeling

The WICHAM01/FLDAAM01 Modules are labeled with FCC ID and

IC Certication Number. If the FCC ID and IC Certication Number

are not visible when the module is installed inside another device,

then the outside of the device into which the module is installed

must also display a label referring to the enclosed module. In that

case, the nal end product must be labeled in a visible area or

display the following:

“Contains FCC ID: A5UWICHAM01”

“Contains IC: 10248A-WICHAM01”

or

“Contains FCC ID: A5UFLDAAM01”

“Contains IC: 10248A-FLDAAM01”

The OEM of the WICHAM01/FLDAAM01 Module must only use the

approved antenna(s), which have been certied with this module.

The OEM integrator has to be aware not to provide information to

the end user regarding how to install or remove this RF module

or change RF related parameters in the user manual of the end

product.

The user manual for the end product must include the

following information in a prominent location:

“To comply with FCC and Industry Canada RF radiation exposure

limits for general population, the antenna(s) used for this

transmitter must be installed such that a minimum separation

distance of 20 cm is maintained between the radiator (antenna)

and all persons at all times and must not be co-located or

operating in conjunction with any other antenna or transmitter.”

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Whirlpool UDT518SAHP Lavavajillas. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Whirlpool. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Whirlpool UDT518SAHP Lavavajillas en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Whirlpool Lavavajillas
Más manuales de Lavavajillas

Preguntas frecuentes sobre Whirlpool UDT518SAHP Lavavajillas

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Whirlpool WDT750SAKZ Lavavajillas

Manual de uso

Whirlpool WIC 3B16 Lavavajillas

Manual de uso

Whirlpool W7F HS41 X Lavavajillas

Manual de uso

Whirlpool WFF 4O33 DLTG X @ Lavavajillas

Manual de uso

Whirlpool ADP AQUAFEEL Lavavajillas

Manual de uso

Whirlpool ADPF 862 IX Lavavajillas

Manual de uso

Whirlpool ADP QUALITY Lavavajillas

Manual de uso

Whirlpool WSIP 4O23 PFE Lavavajillas

Categorias relacionadas