Manual de uso Worx WG385 Sierra de cadena

Manual de uso

Cordless Chainsaw EN

4

b) Do not expose battery pack to heat or fire. Avoid

storage in direct sunlight.

c) Do not short-circuit a battery pack. Do not store

battery packs haphazardly in a box or drawer

where they may short-circuit each other or be

short-circuited by conductive materials. When

battery pack is not in use, keep it away from other

metal objects, like paper clips, coins, keys, nails,

screws or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

d) Do not remove battery pack from its original

packaging until required for use.

e) Do not subject battery pack to mechanical shock.

f) In the event of battery leaking, do not allow the

liquid to come into contact with the skin or eyes.

If contact has been made, wash the affected area

with copious amounts of water and seek medical

advice.

g) Observe the plus (+) and minus (–) marks on the

battery back and equipment and ensure correct

use.

h) Do not use any battery pack which is not

designed for use with the equipment.

i) Keep battery pack out of the reach of children.

j) Seek medical advice immediately if a cell or

battery pack has been swallowed.

k) Always purchase the battery pack recommended

by the device manufacturer for the equipment.

l) Keep battery pack clean and dry.

m) Wipe the battery pack terminals with a clean dry

cloth if they become dirty.

n) Battery pack needs to be charged before use.

Always use the correct charger and refer to

the manufacturer’s instructions or equipment

manual for proper charging instructions.

o) Do not leave battery pack on prolonged charge

when not in use.

p) After extended periods of storage, it may

be necessary to charge and discharge the

battery pack several times to obtain maximum

performance.

q) Battery pack gives its best performance when it

is operated at normal room temperature (20 °C ±

5 °C).

r) When disposing of battery packs, keep battery

packs of different electrochemical systems

separate from each other.

s) Recharge only with the charger specified by

Worx. Do not use any charger other than that

specifically provided for use with the equipment.

A charger that is suitable for one type of battery pack

may create a risk of fire when used with another

battery pack.

t) Retain the original product literature for future

reference.

u) Use only the battery pack in the application for

which it was intended.

v) Remove the battery from the equipment when

not in use.

w) Dispose of properly.

SAVE THESE INSTRUCTIONS

Instructions concerning the proper techniques for

basic felling, limbing, and cross-cutting

1. Felling a tree

When bucking and felling operations are being performed

by two or more persons at the same time, the felling

operations should be separated from the bucking

operation by a distance of at least twice the height of the

tree being felled. Trees should not be felled in a manner

that would endanger any person, strike any utility line or

cause any property damage. If the tree does make contact

with any utility line, the company should be notified

immediately.

The Chain saw operator should keep on the uphill side of

the terrain as the tree is likely to roll or slide downhill after

it is felled.

An escape path should be planned and cleared as

necessary before cuts are started. The escape path should

extend back and diagonally to the rear of the expected line

of fall as illustrated in Figure 1.

Before felling is started, consider the natural lean of the

tree, the location of larger branches and the wind direction

to judge which way the tree will fall.

Remove dirt, stones, loose bark, nails, staples and wire

from the tree.

2. Notching undercut

Make the notch 1/3 the diameter of the tree, perpendicular

to the direction of falls as illustrated in Figure 2. Make the

lower horizontal notching cut (W) first. This will help to

avoid pinching either the saw chain or the guide bar when

the second notch (X) is being made.

3. Felling back cut

Make the felling back cut (Y) at least 2’’ higher than the

horizontal notching cut as illustrated in Figure 2. Keep the

felling back cut parallel to the horizontal notching cut.

Make the felling back cut so enough wood is left to act

as a hinge. The hinge wood keeps the tree from twisting

and falling in the wrong direction. Do not cut through the

hinge.

As the felling gets close to the hinge, the tree should begin

to fall. If there is any chance that the tree may not fall in

desired direction or it may rock back and bind the saw

chain, stop cutting before the felling back cut is complete

and use wedges of wood, plastic or aluminium (Z) to open

the cut and drop the tree along the desired line of fall ( ).

When the tree begins to fall remove the Chain saw from

the cut, stop the motor, put the Chain saw down, then use

the retreat path planned ( ). Be alert for overhead limbs

falling and watch your footing.(See Fig.1)

3

2

2

W

Y

Z

X

2˝

2˝

1

1

1

2

2/3

1

1/3

1

2

2/3

1/3

Fig.1

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Worx WG385 Sierra de cadena. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Worx. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Worx WG385 Sierra de cadena en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Worx Sierras de cadena
Más manuales de Sierras de cadena

Preguntas frecuentes sobre Worx WG385 Sierra de cadena

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Worx WG324E Sierra de cadena

Manual de uso

Worx WG322E Sierra de cadena

Manual de uso

Worx WG325.KIT Sierra de cadena

Manual de uso

Worx WG307 Sierra de cadena

Manual de uso

Worx WG323E Sierra de cadena

Manual de uso

Worx WG349E Sierra de cadena

Manual de uso

Worx WG324 Sierra de cadena

Manual de uso

Worx WG325.1 Sierra de cadena

Categorias relacionadas