Manual de uso Freestyle Shark Classic Tide Reloj de pulsera

Manual de uso

4. Press S3 button, the minute digits will blink.

Press S1 button to increase the digits by one

unit or press S2 button to decrease the digits by

one unit. Holding down either button will speed

up the process.

5. Press S3 button, the alarm frequency setting

will blink. Press S1 button or S2 button to cycle

forward or backward respectively the alarm

frequency setting to be selected (DAILY, WEEK-

DAYS, WEEKENDS, SUN…SAT WKLY(Sunday

through Saturday weekly)).

6. When nished making all the settings, press S4

button to conrm.

NOTE: The alarm time is displayed in the same

time format as in NORMAL TIME mode.

NOTE: The alarm will automatically be activated

after being set.

NOTE: Both ALARM 1 and ALARM 2 function in

accordance with NORMAL TIME (TIME-1) only.

TO TURN ON/OFF THE ALARM:

1. Press S3 button to select ALARM mode.

2. Press S1 button to toggle between ALARM 1

and ALARM 2.

3. Press S2 button to turn on the alarm, the alarm

frequency setting will appear.

4. Press S2 button again to turn off the alarm, the

message “OFF” message will be displayed.

WHEN AN ALARM OR HOURLY CHIME GOES OFF:

A tune will be emitted by the hour when the hourly

chime function is activated.

A 20-second alarm tune will be emitted and the

backlight will ash at the designated time when

the alarm is activated. To stop the tune, press

any button.

If the alarm tune is done without any user interrup-

tion, the watch will automatically enter a snooze

mode. The alarm will go off again after 5 minutes

but for only once.

TO SET THE FORIGN TIME AND CALENDAR:

1. Press S3 button to select TIME 2 mode.

2. Press and hold S4 button for approximately 4

seconds, the message “SET TIME-2” will be

displayed and the year digits will blink. Press

S1 button to increase the digits by one unit or

press S2 button to decrease the digits by one

unit. Holding down either button will speed up

the process.

3. Press S3 button the month digits will blink.

Press S1 button to increase the digits by one

unit or press S2 button to decrease the digits by

one unit. Holding down either button will speed

up the process.

4. Press S3 button, the date digits will blink. Press

S1 button to increase the digits by one unit or

press S2 button to decrease the digits by one

unit. Holding down either button will speed up

the process.

5. Press S3 button, the hour digits (including

A.M./P.M. for 12-hour format) will blink. Press

S1 button to increase the digits by one unit or

press S2 button to decrease the digits by one

unit. Holding down either button will speed up

the process.

6. Press S3 button, the minute digits will blink.

Press S1 button to increase the digits by one

unit or press S2 button to decrease the digits by

one unit. Holding down either button will speed

up the process.

7. When nished making all the settings, press S4

button to conrm.

NOTE: In FOREIGN TIME mode, only the year,

month, date, hour and minute are open to setting.

All other settings are synchronized between NOR-

MAL TIME mode and FOREIGN TIME mode.

TO USE THE BACKLIGHT:

Press S5 button to turn on the backlight for ap-

proximately 3 seconds.

To reduce carbon foot print, these

SHARK instructions are printed with

soy inks on recycled paper.

ENGLISH

SUNSET TIME:

In SUNSET TIME mode, Press S1 button or S2

button to display the previous and the next sunset

time respectively.

NOTE: In all of the three data display modes, you

can press and hold S1 button or S2 button until the

“SCAN” message appears to initiate date scanning

in the forward or backward direction respectively.

Release either button when the desired date is

displayed.

After abandoning the date scanning procedure,

while the “SCAN” message is still displayed,

press S1 button or S2 button to move forward or

backward respectively the displayed date by one

day. Press and hold the corresponding buttons

to reinitiate date scanning. Scanning will stop

automatically if the last date for which there is no

tide data is reached.

NOTE: If there is no tide data for the date, the

message “NO TIDE DATA FOR THE DATE” will be

displayed.

NOTE: The time and calendar format will be the

same as that of the NORMAL TIME mode.

TO USE THE CHRONOGRAPH:

1. Press S3 button to select CHRONOGRAPH mode.

2. The chronograph will be displayed in its current

state – stopped, running or reset.

3. To resume a stopped counting, press S1 button

to resume from where it left off.

4. To start a new counting, reset the chronograph

to zero rst.Press S2 button to stop counting,

then press and hold S2 button to reset counter

to zero.

For the measurement of elapsed time:

In CHRONOGRAPH mode,

1. Press S1 button to start counting.

2. To stop counting, press S2 button. Press S1

button to resume from where it left off.

3. To reset to zero, press S2 button to stop counting

and then press and hold S2 button.

NOTE: You can leave the chronograph running

while switching over to other operating modes.

The chronograph indicator

will be displayed in

NORMAL TIME mode and FOREIGN TIME mode

when the timer is in use.

NOTE: The chronograph can count up to a maxi-

mum time of 99:59.59.99 (99 hours:59 minutes.59

seconds.99 hundredths).

TO SET THE TIMER:

1. Press S3 button to select TIMER mode.

2. Press and hold S4 button for approximately 4

seconds, the message “SET TIMER” will be

displayed and the hour digits will blink. Press

S1 button to increase the digits by one unit or

press S2 button to decrease the digits by one

unit. Holding down either button will speed up

the process.

3. Press S3 button, the minute digits will blink.

Press S1 button to increase the digits by one

unit or press S2 button to decrease the digits by

one unit. Holding down either button will speed

up the process.

4. Press S3 button, the second digits will blink.

Press S1 button to increase the digits by one

unit or press S2 button to decrease the digits by

one unit. Holding down either button will speed

up the process.

5. Press S3 button, the action-at-end* setting will

blink. Press S1 button or S2 button to select

among STOP AT END, REPEAT AT END and

UP AT END.

6. When nished making all the settings, press S4

button to conrm the settings.

NOTE*: Illustration of the action-at-end setting:

a) STOP AT END – the timer will stop when the

countdown reaches zero.

b) REPEAT AT END – the timer will reload and

repeat the countdown when the countdown

reaches zero with repetition number updated.

c) UP AT END – the timer will count up to a maxi-

mum of 23 hours, 59 minutes and 59 seconds

when the countdown reaches zero.

TO USE THE TIMER:

1. Press S3 button to select TIMER mode.

2. Press S1 button to start counting.

3. To stop counting, press S2 button. Press S1 but-

ton to resume from where it left off.

4. To reload the timer, press S2 button to stop

counting and then press S2 button again.

5. Upon completion of a countdown, the watch

will react according to the action-at-end setting

selected:

If STOP AT END is selected, the timer will stop

when the countdown reaches zero. A timer alert

tune will be emitted and the backlight will ash.

If REPEAT AT END is selected, the timer will

reload and repeat the countdown when the

countdown reaches zero with repetition number

updated. If the timer is set to be less than 30

seconds, the timer will repeat with a beep gener-

ated; if the timer is set to be 30 seconds or more,

the timer will repeat with a timer alert tune

generated and the backlight will ash.

If UP AT END is selected, the timer will count up

to a maximum of 23 hours, 59 minutes and 59

seconds when the countdown reaches zero. A

timer alert tune will be emitted and the backlight

will ash.

NOTE: Regardless of the action-at-end setting

selected, when a countdown reaches the nal 1

minute, a “beep-beep-beep” sound will be emitted.

When it reaches the nal 30 seconds, a “beep-

beep” sound will be emitted. When it reaches the

nal 10 seconds, a “beep” sound will be emitted

every second.

NOTE: You can leave the timer running while

switching over to other operating modes. The timer

indicator

(STOP AT END) / (REPEAT AT END)

/

(UP AT END) will be displayed in NORMAL

TIME mode and FOREIGN TIME mode when the

timer is in use.

TO SET THE HEAT TIMER:

1. Press S3 button to select HEAT TIMER mode.

2. Press and hold S4 button for approximately 4

seconds, the message “SET HEAT TIMER” will be

displayed and the minute digits will blink.

3. Press S1 button to increase the digits by ve

units, or press S2 button to decrease the digits

by ve units. Holding down either button will

speed up the process.

4. When nished making all the settings, press S4

button to conrm.

NOTE: The heat timer can count up to a maximum

time of 35.00 (35 minutes).

TO USE THE HEAT TIMER:

1. Press S3 button to select HEAT TIMER mode.

2. Press S1 button to start counting.

3. To stop counting, press S2 button. Press S1

button to resume from where it left off.

4. To reload the heat timer, press S2 button to stop

counting and then press S2 button again.

5. Upon completion of a countdown, a heat timer

alert tune will be emitted and the backlight will

ash.

NOTE: When a countdown reaches the nal 1

minute, a “beep-beep-beep” sound will be emitted.

When it reaches the nal 30 seconds, a “beep-

beep” sound will be emitted. When it reaches the

nal 10 seconds, a “beep” sound will be emitted

every second.

NOTE: You can leave the heat timer running while

switching over to other operating modes. The heat

timer indicator

will be displayed in NORMAL

TIME mode and FOREIGN TIME mode when the

timer is in use.

NOTE: The heat timer is independent of the timer.

Both may be running at the same time.

TO SET THE ALARM TIME:

1. Press S3 button to select ALARM mode.

2. Press and hold S4 button for approximately 4

seconds, the message “SET ALARM” will be

displayed and the alarm entry setting will blink.

Press S1 button or S2 button to toggle between

ALARM 1 and ALARM 2 to set.

3. Press S3 button, the hour digits (including

A.M./P.M. for 12-hour format) will blink. Press

S1 button to increase the digits by one unit or

press S2 button to decrease the digits by one

unit. Holding down either button will speed up

the process.

SHARK-FS1204-CLASSIC TIDE-AG9151-R01

Current date

Time of the

next sunset

SHARK_FS1204-Classic TIDE_AG9151-R01.indd 3 6/26/12 11:14:12 AM

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Freestyle Shark Classic Tide Reloj de pulsera. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Freestyle. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Freestyle Shark Classic Tide Reloj de pulsera en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Freestyle Relojes de pulsera
Más manuales de Relojes de pulsera

Preguntas frecuentes sobre Freestyle Shark Classic Tide Reloj de pulsera

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Freestyle Hammerhead Reloj de pulsera

Manual de uso

Freestyle Shark Clip Reloj de pulsera

Manual de uso

Freestyle Shark Classic Reloj de pulsera

Manual de uso

Freestyle Mariner Reloj de pulsera

Manual de uso

Freestyle Shark Mini Reloj de pulsera

Manual de uso

Naviforce NF9135 Reloj de pulsera

Manual de uso

Oris Coulson Limited Edition Reloj de pulsera

Manual de uso

Timex TW2V44700ZV Marlin Reloj de pulsera

Categorias relacionadas