Manual de uso Bosch GSR 18V-110 C Atornillador taladrador

Manual de uso

English | 19

reactions and/or lead to respiratory infections of the user or

bystanders.

Certain dust, such as oak or beech dust, is considered carci-

nogenic, especially in connection with wood-treatment ad-

ditives (chromate, wood preservative). Materials containing

asbestos may only be worked by specialists.

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the ma-

terials to be worked.

u Avoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

Starting Operation

Inserting the battery

Note: The use of batteries unsuitable for your power tool can

lead to malfunctions or damage to the power tool.

Set the rotational direction switch (16) to the middle posi-

tion to avoid unintentionally switching it on. Insert the

charged battery (11) into the handle until you feel it engage

and it is flush with the handle.

Setting the rotational direction (see figure B)

The rotational direction switch (16) is used to change the ro-

tational direction of the power tool. However, this is not pos-

sible while the on/off switch (17) is being pressed.

Rotate clockwise: Slide the rotational direction

switch (16) on both sides until it stops in the posi-

tion.

Rotate anti-clockwise: Slide the rotational direction

switch (16) on both sides until it stops in the posi-

tion.

Setting the operating mode

Drilling

Set the mode selector switch(8) to the

"drilling" symbol.

Screwdriving

Set the mode selector switch(8) to the "screw-

driving" symbol.

Impact drilling(GSB 18V-110 C)

Set the mode selector switch(8) to the "impact

drilling" symbol.

Switching on/off

To start the power tool, press and hold the on/off switch

(17).

The LED (13) lights up when the on/off switch (17) is lightly

or fully pressed, meaning that the work area is illuminated in

poor lighting conditions.

To switch off the power tool, release the on/off switch (17).

Adjusting the Speed

You can adjust the speed of the power tool when it is on by

pressing in the on/off switch (17) to varying extents.

A light pressure on the on/off switch (17) results in a low ro-

tational speed. Increased pressure on the switch causes an

increase in speed.

Preselecting torque (applies to screwdriving mode)

The torque presetting ring (7) can be used to preselect the

required torque in 25 stages. Once the set torque has been

reached, the application tool will be stopped.

Mechanical gear selection

u Only operate the gear selector (9) when the power

tool is not in use.

First gear:

Low speed range; for working with a large drilling diameter

or for screwdriving.

Second gear:

High speed range; for working with a small drilling diameter.

u Always push the gear selector switch as far as it will

go. Otherwise, the power tool may become damaged.

Temperature-dependent overload protection

When used as intended, the power tool cannot be over-

loaded. In the event of overloading or the temperature

rising/falling outside the permitted operating temperature

range, the speed will be reduced. The power tool will not run

at full speed again until the permitted operating temperature

has been reached.

Activation of the temperature-controlled overload protector

is indicated by the LED (14) on the power tool lighting up

red. To return to within the permitted operating temperature

range, switch the gear selector (9) to first gear, run the

power tool at no load or wait until the LED (14) goes out.

When the LED (14) has gone out, the tool has returned to

within the permitted operating temperature range.

Emergency switch-off (KickBack Control)

The emergency switch-off function (Kick-

Back Control) gives the user greater control

over the power tool and offers them better

protection than power tools that do not

have KickBack Control. The power tool will switch off if it

suddenly and unforeseeably rotates around the drilling

axis.

Rapid shut-off is indicated by the LED on the power tool

flashing.

To switch the tool back on, release the on/off switch and

then press it again.

u If the Kickback Control function is defective, it will no

longer be possible to switch the power tool on. Have

the power tool serviced by a qualified repair person

using only original replacement parts.

Connectivity functions

In conjunction with the Bluetooth® Low Energy Module

GCY30-4, the following connectivity functions are available

for the power tool:

Bosch Power Tools 1 609 92A 60C | (07.08.2020)

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Bosch GSR 18V-110 C Atornillador taladrador. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Bosch. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Bosch GSR 18V-110 C Atornillador taladrador en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Bosch Atornilladores taladrador
Más manuales de Atornilladores taladrador

Preguntas frecuentes sobre Bosch GSR 18V-110 C Atornillador taladrador

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Bosch EasyDrill 12 Atornillador taladrador

Manual de uso

Bosch GSR 18V-55 Atornillador taladrador

Manual de uso

Bosch GSR 18V-85 C Atornillador taladrador

Manual de uso

Bosch GSB 36VE-2-LI Atornillador taladrador

Manual de uso

Bosch GSR 12V-15 Atornillador taladrador

Manual de uso

Bosch PSR 14,4-2 Atornillador taladrador

Manual de uso

Bosch PSR 10,8 LI-2 Atornillador taladrador

Manual de uso

Bosch GSR 10.8-2-LI Professional Atornillador taladrador

Categorias relacionadas