08 GB
Selecting a zone
When zone is already ON a lower lighting intensity for the not selected
zones that are ON is produced.
If only one zone is ON, this zone is already selected by default, without
needing to short press (150 msec) over selection key.
Increase / Decrease power level
3. With a zone ON at 0 power level, if the zone is hot, 0 will blink
alternatively. After 10 seconds, 0 will disappear an ‘H’ letter will appear
fixed on display.
With a short press on ‘+’ or ‘-‘ keys, Increase or decrease power in the
selected zones digit: 0-1-2-3...9-P
1. For Long Presses in + or - keys, power level increases /decreases
continuously. With a fast increase, power stops at level 9, and for a
higher power another short press is needed on the + key. No beep
sound is heard with fast increase / decrease.
2. Once arrived to P power level, pressing + key again does not
change power level to 0.Once arrived to 0 power level, pressing - key
again does not change power level to P.
4. When a heater is selected and ‘+’ & ‘-‘keys are touched at the same
time, power level will go to ‘0’ but heater will maintain selected during
10 seconds. If heater was temporized, timer will go to Off. This action
can only be developed in several cases depending touch control
configuration.The following examples are for information only.
Personal experience should then let you adapt these settings to your
taste and habit
Child Lock option
To deactivate Child Lock, follow the same process explained before.
Then Short beep will be heard and displays will show "n" letter. Hob will
remain unlocked.
Note: An automatic child lock will produce in 15 minutes after total
Switch OFF of the hob.
This action will be done when ‘+’ & ‘-‘keys were touched at the same
time.
Then, any time when a key will be touched, displays will show "L"
during 2sec. heating remains at the same state.
To switch ON double extension ring, associated main zone must be
already ON and Indicating power level must be higher than 0.
2nd Short Press on extension key Switches OFF extension ring.
8.1- Double zone ON
1st Short Press on extension key Switches ON 1st extension ring. 1
LED over extension key turns ON if 1st extension ring is ON (left LED in
case of triple zone, middle and only LED in case of double zone) 2nd
Short Press on extension key Switches ON 2nd extension ring.
1st Short Press on extension key Switches ON extension ring. LED
over extension key turns ON if Extension ring is ON.
8.2- Triple zone ON
Short beep each press on extension key.
Double / Triple zones
Bridge function
The bridge can be enabled only when both heaters are off. One heater
of the bridge has been selected, to activate bridge function touch
bridge key.
A beep sounds and the zone LED is switched on if the zone is enabled.
Once the heaters selected, if the power level is not the desired power
level, by the + - keys.
The function will finish:
- If user selects power level “0”
- If the bridge key is touched in setting mode
Both bridge heaters will be selected at the same time.
Both bridge heater displays will show same power level.
Overflow security
Something (an object or a liquid) is pressing any key during more than
5s. 2 Short Beep + 1 Long beep every 30s while the key is pressed.
Cook-top will turn Off. This symbol will maintain blinking while the
matter persist.
Timer
Timer function can be activated with its own key.
Select the zone to be timed. Power level of the zone greater than 0.
Static is displayed in the zone being timed . "0 0" in the digits
reserved for the timer.
1) With "+" or "-" keys, timer time can be chosen. No Beeps at time
change.
2) Pressing continuously timer key, the timer is cancelled (goes to 00).
3) If timer "+" or "-" keys is maintained pressed there is quick setting.
4) When setting timer time, it is possible to go from "00" to "99" with "-"
key, and from "99" to "00" with "+" key.
5) Maximum time 99 minutes.
Short beep each press on extenson key.
2 LEDs over extenson key turn ON f 1st and 2nd extenson rngs are
ON 3rd Short Press on extenson key. Swtches OFF 1st and 2nd
extenson rngs.
Residual Heat Indicator (In radiant heaters-> calculated)
While a temperature on the cook top glass surface is above
o
65 Cb(theory value), this condition will be shown in the associated
display, by means of an “H”.
The same indicators can be used for “residual heat” indication as well.
A time table must be defined on this purpose: Rest Heat time=f (power
level, working time).
o
To generate a temperature above 65 C a heating element has to be in
operation for certain time, this time depends on the power level. Once
this time has expired, the residual heat warning will be shown when
the heating element is switched off.
7) It s possble to adjust the tmer tme whle the tmer s prevously
runnng.
8) Power of tmed zone can be modfed wthout consequences on the
tmer programmng.
9) Last mnute wll be dsplayed by seconds (For Varants only vsble f
we enter the tmer programmng whle the last mnute of the
countdown)
10) Pressng the Tmer key wthout any selected zone and when no
zone s beng tmed, does nothng.
11) Pressng the Tmer key wthout any selected zone and when many
zones are beng tmed, the tme shown n tme dgts changes n a
rotatory way, and shows the tme whose power dsplay has the
decmal pont ON.
12) Alternatvely Power (5s) and (0,5s) s dsplayed n the zone beng
tmed.
Remanng tme s dsplayed n the dgts reserved for the tmer. If
multple zones are tmed, the smallest remanng tme s dsplayed,
and the decmal pont s dsplayed n the correspondng zone.
6) When the tme s elapsed and the hob s beepng, press any key and
the alarm and dgt sequence wll end.
Únase a la conversación sobre este producto
Aquí puedes compartir lo que piensas sobre Candy CH64CCB/S Placa. Si tiene alguna pregunta, primero lea atentamente el manual. Puede solicitar un manual utilizando nuestro formulario de contacto.