Manual de uso Candy PMI640N Placa

Manual de uso

Installing a domestic appliance can be a complicated operation which if not carried out correctly, can seriously affect consumer

safety. It is for this reason that the task should be undertaken by a professionally qualified person who will carry it out in

accordance with the technical regulations in force. In the event that this advice is ignored and the installation is carried out

by an unqualified person, the manufacturer declines all responsibility for any technical failure of the product whether or not

it results in damage to goods or injury to individuals.

2 GB

BUILT-IN

The furniture in which your hob will be installed and all adjacent

furniture, should be made from materials that can withstand high

temperatures. In addition, all decorative laminates should be fixed

with heat-resistant glue.

Installation:

• A watertight seal is supplied with the hob.

Before fitting:

- turn the hob upside down, with the glass surface facing downwards.

Make sure the glass is protected.

- fit the seal round the hob.

- make sure that it is correctly fitted to avoid any leakage into the

supporting cabinet.

• It is important to fit the hob on a level supporting surface.

• Deformations caused by incorrect fitting can alter the specifications

of the worktop and the performance of the hob.

• Leave a gap of at least 5 cm between the appliance and any

neighbouring vertical surfaces.

• It is absolutely essential that the recess conforms with the

dimensions indicated.

• The height of the flush-mounted part of the hob is 5,5 cm.

• If there is an intermediate division :

- the clearance between the bottom of the casing and an

intermediate floor or part of a furniture unit must greater than

2,5 cm so as to allow air circulate.

The minimum distance should be 8 cm.

- furthermore, you should ensure that there is at the rear a

ventilation (8 cm) on all the width.

• You can not build the hob in above an oven with no fan, a

dishwasher, fridge, freezer or washing machine.

• The body of the hob is fitted which 4 location holes to take the

fixing clamps intended to fix the hob in the unit. Place the 4 fixing

clamps, before building-in the hob, in such a way that the hob

is placed perfectly in the support unit.

INSTALLATION

"The installation must conform to the standard directives."

The manufacturer declines all responsibility for any damage that

may be caused by unsuitable or unreasonable use.

Warning :

• Always check before any electrical operation, the supply tension

shown on the electricity meter, the adjustment of the circuit-

breaker, the continuity of the connection to earth to the installation

and that the fuse is suitable.

• The electrical connection to the installation should be made via

a socket with a plug with earth, or via an omnipole cut-out switch

with an opening gap of at least 3 mm.

If the appliance has a socket outlet, it must be installed so that

the socket outlet is accessible.

• The yellow/green wire of the power supply cable must be

connected to the earth of both power supply and appliance

terminals.

• The manufacturer cannot be held responsible for any accidents

resulting from the use of an appliance which is not connected

to earth, or with a faulty earth connection continuity.

• Any queries regarding the power supply cord should be referred

to After Sales Service or a qualified technician.

ELECTRICAL CONNECTION

Seal

Hob

25 mm

mini

50 mm

Opening

500 X 50

Opening

500 X 10

It is however possible to connect the hob to :

. Three phase 220-240 V3~

. Three phase 380-415 V3N~

To proceed to the new connection, you must adhere the

following instructions.

• Before making the connection, make sure that the installation

is protected by a suitable fuse, see table, and that it is fitted with

wires of a large enough section to supply the appliance normally.

• Connect to a socket, to choose the correct fuse, you must

refer on the table.

The hob is fitted with a power supply cord which allows it to be

connected only to a power supply of 220-240 V between phases

or between phase and neutral.

CONNECTION TO THE TERMINALS ON THE TERMINAL BLOCK:

Operations to be carried out on the existing connection :

• Turn over the hob, glass side against the work top, taking care

to protect the glass.

• Open the cover.

• remove the screws retaining the terminal block which contains

the shunt bars and the conductors of the supply cord,

• unscrew the cable clamp to release the power supplying cord.

• Pull out the supply cord.

• Operations to be carried out to make a new connection :

- Choose the power supply cable in accordance with the

recommendations in the table.

- Pass the power supply cable into the clamp.

- Strip the end of each conductor of the supply cord on a 10 mm

length, by taking in account the requested length of the cord for

the connection to the terminal block.

- According to the installation and with the help of shunt bars

which you should have recovered in the first operation, fix the

conductor as shown on the chart.

- Screw the cable clamp and fix the cover.

Note: make sure the terminal board screws are tight.

FOR PMI 640 MODEL

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Candy PMI640N Placa. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Candy. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Candy PMI640N Placa en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Candy Placas
Más manuales de Placas

Preguntas frecuentes sobre Candy PMI640N Placa

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Candy CHW6LBX NL Placa

Manual de uso

Candy PGC750SQX Placa

Manual de uso

Candy CHW6LBX/4U2 Placa

Manual de uso

Candy PCT25CBCH64CCB Placa

Manual de uso

Candy CHW6BLB Placa

Manual de uso

Candy CDK6GF4WEKB Placa

Manual de uso

Candy CI633C/E1 Placa

Manual de uso

Candy CI633CTT Placa

Categorias relacionadas