Manual de uso Hikoki G 18DSL2 Amoladora angular

Manual de uso

12

English

MAINTENANCE AND INSPECTION

1. Inspecting the depressed center wheel

Ensure that the depressed center wheel is free of cracks

and surface defects.

2. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws be

loose, retighten them immediately. Failure to do so could

result in serious hazard.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the power

tool. Exercise due care to ensure the winding does not

become damaged and/or wet with oil or water.

4. Inspecting the carbon brushes (Fig. 12)

The motor employs carbon brushes which are

consumable parts. Since and excessively worn carbon

brush can result in motor trouble, replace the carbon

brush with new ones when it becomes worn to or near

the “wear limit” ⓐ. In addition, always keep carbon

brushes clean and ensure that they slide freely whithin

the brush holders.

NOTE

When replacing the carbon brush with a new one, be

sure to use the HiKOKI Carbon Brush Code No. 999101.

5. Replacing carbon brushes (Fig. 12)

Take out the carbon brush by fi rst removing the brush

cap and then hooking the protrusion of the carbon brush

with a fl at head screw driver, etc.

When installing the carbon brush, choose the direction

so that the nail ⓑ of the carbon brush agrees with the

contact portion ⓒ outside the brush tube. Then push it in

with a fi nger. Lastly, install the brush cap.

CAUTION

Be absolutely sure to insert the nail of the carbon brush

into the contact portion outside the brush tube. (You can

insert whichever one of the two nails provided).

Caution must be exercised since any error in this

operation can result in the deformed nail of the carbon

brush and may cause motor trouble at an early stage.

6. Inspection of terminals (tool and battery)

Check to make sure that swarf and dust have not

collected on the terminals.

On occasion check prior, during and after operation.

CAUTION

Remove any swarf or dust which may have collected on

the terminals.

Failure to do so may result in malfunction.

7. Cleaning on the outside

When the cordless disc grinder is stained, wipe with a

soft dry cloth or a cloth moistened with soapy water. Do

not use chloric solvents, gasoline or paint thinner, for

they melt plastics.

8. Cleaning the fi lter

After use, remove any grime or dust from the fi lter with an

airgun or other tool.

9. Storage

Store the cordless disc grinder in a place in which the

temperature is less than 40°C, and out of reach of children.

NOTE

Storing lithium-ion batteries.

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage (3 months or more) of batteries with

a low charge may result in performance deterioration,

signifi cantly reducing battery usage time or rendering

the batteries incapable of holding a charge.

However, signifi cantly reduced battery usage time may

be recovered by repeatedly charging and using the

batteries two to fi ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries dead

and purchase new batteries.

CAUTION

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

Important notice on the batteries for the HiKOKI

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used with

batteries other than these designated by us, or when

the battery is disassembled and modifi ed (such as

disassembly and replacement of cells or other internal

parts).

GUARANTEE

We guarantee HiKOKI Power Tools in accordance with

statutory/country specifi c regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling instruction,

to a HiKOKI Authorized Service Center.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 96 dB (A).

Measured A-weighted sound pressure level: 85 dB (A).

Uncertainty K : 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN60745.

Surface grinding:

Vibration emission value

a

h

, AG = 10.1 m/s

2

Uncertainty K = 1.5 m/s

2

The declared vibration total value has been measured in

accordance with a standard test method and may be used

for comparing one tool with another.

It may also be used in a preliminary assessment of exposure.

WARNING

○ The vibration emission during actual use of the power

tool can diff er from the declared total value depending in

the ways in which the tool is used.

○ Identify safety measures to protect the operator that

are based on an estimation of exposure in the actual

conditions of use (taking account of all parts of the

operating cycle such as the times when the tool is

switched off and when it is running idle in addition to the

trigger time).

NOTE

Due to HiKOKI’s continuing program of research and

development, the specifi cations herein are subject to

change without prior notice.

000BookG18DSL2EU.indb12000BookG18DSL2EU.indb12 2020/09/2514:21:552020/09/2514:21:55

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Hikoki G 18DSL2 Amoladora angular. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Hikoki. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Hikoki G 18DSL2 Amoladora angular en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Hikoki Amoladoras angulares
Más manuales de Amoladoras angulares

Preguntas frecuentes sobre Hikoki G 18DSL2 Amoladora angular

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Hikoki G 12VA Amoladora angular

Manual de uso

Hikoki G 10SS2 Amoladora angular

Manual de uso

Hikoki G 13BY Amoladora angular

Manual de uso

Hikoki G 23SWU2 Amoladora angular

Manual de uso

Hikoki G 10SN Amoladora angular

Manual de uso

Hikoki G 13YC2 Amoladora angular

Manual de uso

Hikoki G 23SU Amoladora angular

Manual de uso

Hikoki G 13VE Amoladora angular

Categorias relacionadas