Manual de uso Hoover FL700 011 Limpiador de vapor

Manual de uso

3

GB

8. To greatly enhance drying of the oor surface, release trigger and turn Mode selector

dial to the DRY position. [1D] Continue to move cleaner over the area to pick up the dirty

solution.

9. To continue cleaning another area, turn Mode selector dial to WASH position. [1D] Repeat

cleaning motion.

10. Empty Dirty Water Tank or clean the lter when the motor sound becomes higher in pitch

and there is a loss of suction (see “Automatic shut-o” section).

Picking up spills

Your cleaner may also be used to pick up small liquid spills (1L or less, never to exceed 1/4 inch

in depth) on non-carpeted oors.

Turn Mode selector dial to the WASH position and release the trigger. Continue to move

cleaner over the area to pick up the spill.

Transporting your cleaner

1. To move your cleaner from room to room, put handle in upright position, tilt cleaner back

on rear wheels and push forward. [17]

2. The cleaner may also be lifted using the carrying handle (A) on the front of the cleaner.

[18]

Storage

Before storing cleaner:

•  Turn cleaner OFF and disconnect from electrical outlet.

•  Empty and rinse solution and Dirty Water Tanks. Allow to air dry.

•  Press on upper handle release button to lower handle for storage.

•  Make sure that nothing is pressing on the nozzle squeegee.

•  Do not store cleaner on a wood surface unless cleaner is completely dry.

Emptying The Dirty Water Tank

Automatic “Shut O”

An automatic suction shut-o is built into the Dirty Water Tank to prevent the tank from

overowing. When the shut-o activates, the cleaner will not pick up debris and the sound of

the motor will change. The Dirty Water Tank is full and must be emptied.

1. Turn cleaner o and disconnect from electrical outlet.

2. To remove tank, press down on release button (g) and pull tank straight out. [13]

3. Remove tank lid (h). Empty tank. [14]

Note: Although not necessary for satisfactory performance, it is recommended that the Dirty

Water Tank be emptied after dry vacuuming and before wet operation.

Cleaning the Filters

The tank lid contains a washable, reusable lter. Clean this lter when suction is low or reduced.

1. Turn cleaner o and disconnect from electrical outlet.

2. Remove Dirty Water Tank and lid [13&14] Remove lter lid (a), then remove lter (b). [19]

3. Remove loose debris from lter by tapping the lter or gently brushing using your hand.

The lter may also be rinsed for additional cleaning. Allow lter to air dry between uses.

4. Reposition lter.

5. Replace lter lid. Press down rmly until snapped in place. [20]

6. Dry or loose debris will also collect on the lter screen located in the tank lid. To remove

debris from screen, remove the pleated lter from the lid. Remove debris from screen (c).

[21]

7. The lter screen may also be cleaned by rinsing it under running water.

8. Reposition pleated lter in lid. Replace lid onto Dirty Water Tank, pressing down rmly

until snapped in place.

9. To replace Dirty Water Tank, place bottom of tank behind ledge (d) and push tank straight

into cleaner body until it is locked in place. [22]

Cleaning the Nozzle

1. Slide the two nozzle release latches (a) outward. [23]

2. Remove nozzle (b) by pulling straight out. [24]

3. Rinse nozzle under running water. Remove debris from squeegee (c) and wipe with a

damp cloth. [25]

4. To replace nozzle, make sure latches (d) are out. Cleaner should be in the upright position

for easier assembly of the nozzle. Align middle section (e) of nozzle with opening (f) on

cleaner. [26]

5. While holding nozzle in place, slide latches inward to lock in place. [5]

Cleaning and Changing the Brush Assembly

How to Remove

1. Place handle in the upright position. Remove tanks to prevent leaking. Set aside.

2. Pull the two nozzle release buttons (a) out. [23] Remove nozzle. [24] Tilt cleaner back so

handle rests on oor.

3. Push two brush release buttons (g) and remove the brush assembly. [27]

4. The brushes can be washed with a mild detergent and rinsed. Do not use a solvent based

detergent.

MAINTENANCE

FloormateManual__1-4_union.indd 3 10/09/2012 14.00.12

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Hoover FL700 011 Limpiador de vapor. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Hoover. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Hoover FL700 011 Limpiador de vapor en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Hoover Limpiadoras de vapor
Más manuales de Limpiadoras de vapor

Preguntas frecuentes sobre Hoover FL700 011 Limpiador de vapor

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Hoover SSNC1700 011 Steamjet Limpiador de vapor

Manual de uso

Hoover SCB1500 011 Limpiador de vapor

Manual de uso

Hoover JWC60B6/1 011 Limpiador de vapor

Manual de uso

Hoover S2IN1300 011 Steamjet Limpiador de vapor

Manual de uso

Hoover SSNH1300 011 Steamjet Handy Limpiador de vapor

Manual de uso

Hoover S2IN1300C 001 Steamjet Limpiador de vapor

Manual de uso

Hoover CAD1700D 011 Limpiador de vapor

Manual de uso

Hoover S2IN1300 001 Steamjet Limpiador de vapor

Categorias relacionadas