Manual de uso Lightning Audio LA-600M Amplificador para coche

Manual de uso

Model

LA-600M LA-1000MD LA-2000MD LA-3000MD

Power

Rating

MAX

400 x 1 @ 4Ω

600 x 1 @ 2Ω

RMS

200 x 1 @ 4Ω

300 x 1 @ 2Ω

MAX

500 x 1 @ 4Ω

750 x 1 @ 2Ω

1000 x 1 @ 1Ω

RMS

250 x 1 @ 4Ω

375 x 1 @ 2Ω

500 x 1 @ 1Ω

MAX

1000 x 1 @ 4Ω

1500 x 1 @ 2Ω

2000 x 1 @ 1Ω

RMS

400 x 1 @ 4Ω

700 x 1 @ 2Ω

1000 x 1 @ 1Ω

MAX

1500 x 1 @ 4Ω

2250 x 1 @ 2Ω

3000 x 1 @ 1Ω

RMS

600 x 1 @ 4Ω

1000 x 1 @ 2Ω

1400 x 1 @ 1Ω

Crossover

12dB/Oct HP/FULL/LPBP 12dB/Oct Low Pass 12dB/Oct Low Pass 12dB/Oct Low Pass

Crossover

Frequency

Variable

40Hz - 150Hz

Variable

35Hz - 250Hz

Variable

35Hz - 250Hz

Variable

35Hz - 250Hz

Subsonic

Filter

Variable

15Hz - 55Hz

Variable

15Hz - 55Hz

Variable

15Hz - 55Hz

Variable

15Hz - 55Hz

Bass Boost

0 to +12dB @ 45Hz

(Remote Included)

0 to +18dB @ 45Hz

(Remote Included)

0 to +18dB @ 45Hz

(Remote Included)

0 to +18dB @ 45Hz

(Remote Included)

Inputs

RCA RCA / Balanced Input RCA / Balanced Input RCA / Balanced Input

Fuse(s)

25A(2) 30A(2) 50A(2) 70A(2)

Dimensions

(LxWxH)

9.8” x 9.4” x 2.3” 11” x 9.4” x 2.3” 13.8” x 9.4” x 2.3” 15” x 9.4” x 2.3”

Installation

Preliminary Considerations:

• If you feel unsure about installing this system yourself, have it installed by a qualified technician.

• Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any

vehicle.

• Aftermarket amplifiers will put an increased load on the vehicle’s battery and charging system, which can reduce battery and alternator life. It is strongly recom-

mended to upgrade your factory alternator and battery for optimum performance from your new audio system.

CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

1. Choose a mounting location that will be secure and offer plenty of unobstructed space for proper cooling. Then plan the wire routing. Keep RCA cables close

together but isolated from the amplifier’s power cables and any high power auto accessories, especially electric motors. When feeding the wires through the fire

wall or any metal barrier, protect them with plastic or rubber grommets to prevent short circuits. Leave the wires long at this point to adjust for a precise fit at

a later time.

NOTE: Never run wires underneath the vehicle.

2. Prepare the power cable for attachment to the amplifier by stripping 1/2” of insulation from the end of the wire. Insert the bared wire into the B+ terminal and

tighten the setscrew to secure the cable in place.

3. Trim the power cable within 18” of the battery and strip1/2”of insulation from the end of the wire.

4. Strip 1/2” from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery positive terminal.

DO NOT install the fuse at this time.

NOTE: ALWAYS protect the battery and electrical system from damage with proper fusing.

5. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the end of the wire and

attach a ring connector. Fasten the cable to the chassis using a non-anodized screw and a star washer. Prepare the grounding cable for attachment to the amplifier

by stripping 1/2” of insulation from the other end of the wire. Insert the bared wire into the GND terminal and tighten the setscrew to secure the cable in place.

6. Prepare the REM turn-on wire for connection to the amplifier by stripping 1/2” of insulation from the wire end. Insert the bared wire into the REM terminal

and tighten the setscrew to secure the cable into place. Connect the other end of the REM wire to a switched 12-volt positive source.

NOTE: The switched voltage is usually taken from the source unit’s accessory/remote lead.

7. Securely mount the amplifier to the vehicle or amp rack. Remember: Think before you drill!

NOTE: Be careful not to mount the amplifier on cardboard or plastic panels.

8. Connect the source signal to the amplifier by plugging the RCA cables/high level inputs into the input jacks at the amplifier. Use only one input configuration.

Using both the RCA and High Level inputs will cause undesirable operation. When using a Master/Slave configuration (MD models only), select which amplifier

will be the master, then set the mode switch to Master and connect RCA cables to the input jacks. The Slave amplifier(s); set the mode switch to Slave and connect

RCA cables to the Slave in/out jacks from the Master’s Slave in/out jacks.

NOTE: When using High Level Inputs, if audible engine noise is present, connect the Black wire to chassis ground. If noise is still present, contact your local

authorized dealer or Lightning Audio customer service. When using a Master/Slave setup do not exceed more than two amplifiers. (MD models only)

9. Connect the speakers. Strip the speaker wires 1/2” and insert into the speaker terminal and tighten the setscrew to secure into place. Be sure to maintain

proper speaker polarity. DO NOT chassis ground any of the speaker leads as unstable operation may result.

NOTE: Mono amplifier speaker outputs (A & B) are wired in parallel internally.

10. Perform a final check of the completed system wiring to ensure that all connections are accurate. Check all power and ground connections for frayed wires

and loose connections. Complete the installation by installing the proper value fuse.

Operation

Adjusting Level: To adjust the level setting, turn the amplifier gain level to the lowest setting. Turn the source unit volume up until distortion is audible and then

slowly down until the distortion is inaudible (approximately ¾ volume position). Next, increase the amplifier level setting until once again distortion is audible

and then down slowly until the distortion is inaudible.

NOTE: Proper level setting is done by a trained professional utilizing an oscilloscope. For a more in depth setting procedure, contact Lightning Audio Technical

Support. In a Master/Slave setup ONLY adjustments made to the master amplifier will effect the output. (MD models only)

Adjusting Crossover: Select the appropriate position for the crossover filter switch. Turn the crossover adjustment knob to the lowest setting. With the system

playing at normal listening level, turn the crossover adjustment knob up slowly until the desired crossover point is achieved. Example: subwoofers- low pass with

an 80Hz crossover point and full-range- high pass with a 100Hz crossover point

NOTE: Some models include a subsonic filter with a variable 15-40Hz high pass filter designed to prevent frequencies below the audio range from being applied

to the subwoofer from the amplifier. Set this to your personal preference while listening to the system. In a Master/Slave setup ONLY adjustments made to the

master amplifier will effect the output. (MD models only)

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Lightning Audio LA-600M Amplificador para coche. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Lightning Audio. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Lightning Audio LA-600M Amplificador para coche en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Lightning Audio Amplificadores para coche
Más manuales de Amplificadores para coche

Productos relacionados

Manual de uso

Lightning Audio LA-4200 Amplificador para coche

Manual de uso

Lightning Audio LA-3000MD Amplificador para coche

Manual de uso

Lightning Audio LA-2100 Amplificador para coche

Manual de uso

Lightning Audio LA-4100 Amplificador para coche

Manual de uso

Lightning Audio LA-8004 Amplificador para coche

Manual de uso

Lightning Audio LA-2000MD Amplificador para coche

Manual de uso

Lightning Audio LA-51000 Amplificador para coche

Manual de uso

Lightning Audio LA-1600MD Amplificador para coche

Categorias relacionadas