Manual de uso Ryobi ERT1400RV Fresadora de superficie

Manual de uso

5

English

GB

FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR

Position both guides parallel to the desired line of cut and

spaced equal distances from the desired edges of the

groove. Rout along one guide, then reverse direction and

rout along the other guide. Clean out any remaining waste

in the center of the groove freehand.

FITTING AND ADJUSTING THE PARALLEL GUIDE

See Figure 12.

1. Insert the parallel guide into the hole of the router

base.

2. Draw a cutting line on the workpiece.

3. Lower the router body until the cutter is in contact with

the workpiece.

4. Position the router on the cutting line. The outer cutting

edge of the cutter must coincide with the cutting line.

5. Without moving the router, push the guide to the edge

of the workpiece before tightening the lock knob.

ROUTING BY FREEHAND

When used freehand, your plunge router becomes a

 exible and versatile tool. This  exibility makes it possible

to easily rout signs, relief sculptures, etc.. There are two

basic techniques for freehand routing:

 Routing letters, grooves, and patterns into wood.

 Routing out the background, leaving the letters or

pattern raised above the surface.

When freehand routing, we suggest the following:

1. Draw or layout the pattern on workpiece.

2. Choose the appropriate cutter.

NOTE: A core box or V-groove bit is often used for routing

letters and engraving objects. Straight bits and ball mills

are often used to make relief carvings. Veining bits are

used to carve small, intricate details.

3. Rout the pattern in two or more passes. Make the  rst

pass at 25% of the desired depth of cut. This process

will provide better control as well as being a guide for

the next pass.

4. Do not rout deeper than 1/8 in (3.2 mm) per pass or cut.

Follow these directions when routing by freehand:

1. Choose the appropriate cutter, set desired depth of

cut, carefully check set-up, and secure workpiece.

2. Make a test cut in a scrap piece of wood from the

same workpiece if possible.

3. Unlock plunge lock lever to raise cutter from any

preset depth of cut. This also permits raising cutter

inside router base.

4. Place router on workpiece inside pattern to be routed.

5. Grasp handles securely and press the switch to start

your router.

6. Let motor build to full speed, then gradually plunge

cutter into workpiece until stop bar comes into contact

with depth stop.

7. Lock plunge lock lever to secure depth of cut setting.

8. Begin routing out the pattern, continuing until a

complete pass at this depth of cut has been made.

WARNING

Do not use large router bits for freehand routing. Use

of large router bits when freehand routing could cause

loss of control or create other hazardous conditions that

could cause possible serious personal injury.

9. Several cuts that require repositioning of router may

be needed for a particular job. If this situation exists,

unlock plunge lock lever to raise cutter inside router

base after each cut, reposition router for next cut,

gradually plunge cutter into workpiece until stop

bar contacts depth stop, lock plunge lock lever and

continue routing.

10. After all cuts have been made, unlock plunge lock

lever, raise cutter inside router base, remove router

from workpiece, turn off the router, and allow cutter to

come to a complete stop.

ROUTING EDGES

Place router on workpiece, making sure the router bit does

not contact workpiece. Turn router on and let the motor

build to its full speed. Begin your cut, gradually feeding

cutter into workpiece.

WARNING

Keep a  rm grip on router with both hands at all times.

Failure to do so could result in loss of control leading to

possible serious injury.

Upon completion of cut, turn motor off and let it come to a

complete stop before removing router from work surface.

WARNING

Never pull router out of work and place upside down on

work surface before the cutter stops.

CONNECTING A DUST EXTRACTOR

See Figure 13.

The dust extractor hose can be connected to the dust

extraction channel.

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Ryobi ERT1400RV Fresadora de superficie. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Ryobi. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Ryobi ERT1400RV Fresadora de superficie en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Ryobi Fresadoras de superficie
Más manuales de Fresadoras de superficie

Preguntas frecuentes sobre Ryobi ERT1400RV Fresadora de superficie

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Parkside IAN 100129 Fresadora de superficie

Manual de uso

DeWalt DW618M Fresadora de superficie

Manual de uso

Skil 1840 AD Fresadora de superficie

Manual de uso

DeWalt DWE625 Fresadora de superficie

Manual de uso

Makita RP1111C Fresadora de superficie

Manual de uso

Bosch GKF 12V-8 Fresadora de superficie

Manual de uso

Bosch POF 400 A Fresadora de superficie

Manual de uso

FERM PRM1006 Fresadora de superficie

Categorias relacionadas