Manual de uso Tetra Whisper 10-30i Filtro de acuario

Manual de uso

Whisper

®

Internal

Power Filter

1. Replace Tetra

®

Whisper

®

Bio-Bag

®

Cartridge Monthly.

2.

Never: Clean or replace Bio-Foam

®

unless

damaged. Discoloration is normal and

desirable. If excessive buildup occurs,

rinse gently with room temperature

dechlorinated water.

3.

Clean impeller yearly.

5-10i

10-30i

20-40i

Troubleshooting Guidelines

Setup

IMPORTANT:

Always unplug the Internal Filter before

inspecting or disassembling

for any reason.

18-12599

1. Attach the filter hanger to the track on the back of the filter

by aligning the water drops as shown (Fig. 1).

2.

Clip the filter to the back wall of your aquarium frame (Fig. 2). If the hanger

doesn't fit, you may need to order separate suction cups (see spare parts list

on back panel to order).

3. Insert the Filter Cartridge and Bio-Foam

®

as shown (Fig. 3). (Note: the front of

the Bio-Foam

®

is marked “front” and should face the front of the Internal Filter.)

4. See diagram for positioning and max and min water levels. To adjust the

height of your filter, simply slide the filter up or down along the hanger track.

If you can't position the filter to your desired water level, you may need

to order suction cups (see spare parts list to order). For low water level

terrariums, you may set the filter on a ledge or aquarium bottom (Fig. 5).

5. Once the filter and water level is within the recommended parameters,

plug in the filter. Avoid using sand in the aquarium as this clogs the filter.

• Avoid placing sand in the aquarium when using this filter.

• Unplug the unit to clean the filter with a clean wet cloth. If needed,

add white distilled vinegar to the cloth, and rinse thoroughly.

• If the Bio-Foam

®

pad is clogged, gently wash with room temperature water

treated with AquaSafe

®

water conditioner to protect beneficial bacteria.

• When medicating fish, remove the carbon from the Bio-Bag

®

, as

carbon absorbs most medications.

• To service the impeller yearly, or if the motor is noisy, unplug the filter and remove it from the aquarium.

Remove the motor (see illustration A), open its cover, and flush debris with clean water. Soak the impeller in

distilled white vinegar using a cotton swab to wipe debris, and rinse. Replace the motor into the filter and install

it in the aquarium using the instructions in this manual.

• It takes a few weeks for new aquarium water to cycle. “Cycling” a fish tank means growing healthy bacteria

on a new filtration system so it filters out dangerous toxins. Tetra

®

SafeStart

®

aquarium bacteria cycles your

aquarium immediately, so you can add fish right away.

Fig. 1

Fig. 2 Fig. 3 Fig. 4 Fig. 5

UNITED PET GROUP, A DIVISION OF SPECTRUM BRANDS, INC.

UNITED PET GROUP, UNA DIVISIÓN DE SPECTRUM BRANDS, INC.

UNITED PET GROUP, UNE FILIALE DE SPECTRUM BRANDS, INC.

3001 COMMERCE ST., BLACKSBURG, VA 24060

1-800-526-0650 • www.tetra-fish.com

® REGISTERED TRADEMARK AND TM TRADEMARK OF SPECTRUM BRANDS, INC.

MARCA COMERCIAL REGISTRADA ® Y MARCA COMERCIAL TM DE SPECTRUM BRANDS, INC.

® MARQUE DÉPOSÉE ET TM MARQUE DE COMMERCE DE SPECTRUM BRANDS, INC.

© 2017 SPECTRUM BRANDS, INC. • MADE IN CHINA • HECHO EN CHINA • FABRIQUÉ EN CHINE

D

C

B

A

A

B

C

D

1

2

3

4

5

6

7

8

8

7

6

5

4

3

2

1

E

F

E

F

This document contains proprietary and confidenal informaon and is the property of United Pet Group Inc. UPG is part of Pet, Home & Garden, a division of Spectrum Brands, Inc, .

The document is loaned on the condion that neither it nor the informaon contained therein shall be disclosed to others without the express consent of UPG. The document shall be returned to UPG upon its request.

1

XX-XXXX

PRELIMINARY

JLS

XXXXXX

CAT_26038-600

1

X

1

1:1

FINISH

MATERIAL

CAT_26038-600

DRWN

CHKD

APPV

DES

DATE

REVISION

ECN

LTR

DO NOT SCALE DRAWING

FINISH

MATERIAL

REV.

OF

1

SHEET

C

DWG. NO.

CAD FILE:

SIZE

SCALE

CAD GENERATED DRAWING,

DO NOT MANUALLY UPDATE

3001 Commerce St., Blacksburg, Virginia 24060 USA (540)951-5400 FAX: (540)951-5415

UNLESS OTHERWISE SPECIFIED

DIMENSIONS ARE IN INCHES

TOLERANCES ARE:

DECIMALS ANGLES

2 PLC DEC

0.02

1/2

3 PLC DEC

0.005

FRACTIONAL

1/16

Model 5-10i Models 10-30i, 20-40i

Click Fit

OR

Illus. A

Water Level

Niveau d’eau

Minimum Water Level

Niveau d’eau minimum

Intake Area

Zone d’aspiration

IMPORTANT SAFETY INSTRUCTIONS

WARNING – To guard against injury, basic safety precautions should be observed, including the following:

READ AND FOLLOW ALL

SAFETY INSTRUCTIONS

DANGER – TO AVOID POSSIBLE ELECTRIC SHOCK, special care should be taken since water

is employed in the use of aquarium equipment. For each of the following situations, do not attempt repairs by yourself; return the

appliance to an authorized service facility for service or discard the appliance:

1. Unplug the appliance before installing, repositioning, cleaning, or

removing the appliance.

2. If the appliance shows any sign of abnormal water leakage, immediately

unplug it from the power source.

3. Carefully examine the appliance after installation. It should not be plugged in.

4. Do not operate any appliance if it has a damaged cord or plug, or if it is

malfunctioning or has been dropped or damaged in any manner.

5. To avoid the possibility of the appliance plug or receptacle getting wet, position

aquarium stand and tank to one side of a wall-mounted receptacle to prevent

water from dripping onto the receptacle or plug. A “drip loop,” shown in the

figure below, should be arranged by the user for each cord connecting an

aquarium appliance to a receptacle. The “drip loop” is the part of the cord below

the level of the receptacle, or the connector if an extension cord is used, to prevent

water traveling along the cord and coming in contact with the receptacle.

If the plug or receptacle does get wet, DON’T unplug the cord. Disconnect the

fuse or circuit breaker that supplies power to the appliance. Then,

unplug and examine for presence of water in the receptacle.

6. Close supervision is necessary when any appliance is used by or near children.

7. To avoid injury, do not contact moving parts or hot parts such as heaters, reflectors, lamp bulbs, and the like.

8. Always unplug an appliance from an outlet when not in use, before putting on or taking off parts, and before cleaning.

Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.

9. Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance

manufacturer may cause an unsafe condition.

10. Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing.

11. Make sure an appliance mounted on a tank is securely installed before operating it.

12. Read and observe all the important notices on the appliance.

13. If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than

the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.

14. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized

outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician. Never use with an extension cord unless plug can be fully inserted. Do not attempt to defeat this safety feature.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING – To guard against injury, basic safety precautions should be observed, including the following:

READ AND FOLLOW ALL

SAFETY INSTRUCTIONS

DANGER – TO AVOID POSSIBLE ELECTRIC SHOCK, special care should be taken since water

is employed in the use of aquarium equipment. For each of the following situations, do not attempt repairs by yourself; return the

appliance to an authorized service facility for service or discard the appliance:

1. Unplug the appliance before installing, repositioning, cleaning, or

removing the appliance.

2. If the appliance shows any sign of abnormal water leakage, immediately

unplug it from the power source.

3. Carefully examine the appliance after installation. It should not be plugged in.

4. Do not operate any appliance if it has a damaged cord or plug, or if it is

malfunctioning or has been dropped or damaged in any manner.

5. To avoid the possibility of the appliance plug or receptacle getting wet, position

aquarium stand and tank to one side of a wall-mounted receptacle to prevent

water from dripping onto the receptacle or plug. A “drip loop,” shown in the

figure below, should be arranged by the user for each cord connecting an

aquarium appliance to a receptacle. The “drip loop” is the part of the cord below

the level of the receptacle, or the connector if an extension cord is used, to prevent

water traveling along the cord and coming in contact with the receptacle.

If the plug or receptacle does get wet, DON’T unplug the cord. Disconnect the

fuse or circuit breaker that supplies power to the appliance. Then,

unplug and examine for presence of water in the receptacle.

6. Close supervision is necessary when any appliance is used by or near children.

7. To avoid injury, do not contact moving parts or hot parts such as heaters, reflectors, lamp bulbs, and the like.

8. Always unplug an appliance from an outlet when not in use, before putting on or taking off parts, and before cleaning.

Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.

9. Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance

manufacturer may cause an unsafe condition.

10. Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing.

11. Make sure an appliance mounted on a tank is securely installed before operating it.

12. Read and observe all the important notices on the appliance.

13. If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than

the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.

14. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized

outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician. Never use with an extension cord unless plug can be fully inserted. Do not attempt to defeat this safety feature.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

WARNING – To guard against injury, basic safety precautions should be observed, including the following:

READ AND FOLLOW ALL

SAFETY INSTRUCTIONS

DANGER – TO AVOID POSSIBLE ELECTRIC SHOCK, special care should be taken since water

is employed in the use of aquarium equipment. For each of the following situations, do not attempt repairs by yourself; return the

appliance to an authorized service facility for service or discard the appliance:

1. Unplug the appliance before installing, repositioning, cleaning, or

removing the appliance.

2. If the appliance shows any sign of abnormal water leakage, immediately

unplug it from the power source.

3. Carefully examine the appliance after installation. It should not be plugged in.

4. Do not operate any appliance if it has a damaged cord or plug, or if it is

malfunctioning or has been dropped or damaged in any manner.

5. To avoid the possibility of the appliance plug or receptacle getting wet, position

aquarium stand and tank to one side of a wall-mounted receptacle to prevent

water from dripping onto the receptacle or plug. A “drip loop,” shown in the

figure below, should be arranged by the user for each cord connecting an

aquarium appliance to a receptacle. The “drip loop” is the part of the cord below

the level of the receptacle, or the connector if an extension cord is used, to prevent

water traveling along the cord and coming in contact with the receptacle.

If the plug or receptacle does get wet, DON’T unplug the cord. Disconnect the

fuse or circuit breaker that supplies power to the appliance. Then,

unplug and examine for presence of water in the receptacle.

6. Close supervision is necessary when any appliance is used by or near children.

7. To avoid injury, do not contact moving parts or hot parts such as heaters, reflectors, lamp bulbs, and the like.

8. Always unplug an appliance from an outlet when not in use, before putting on or taking off parts, and before cleaning.

Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.

9. Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance

manufacturer may cause an unsafe condition.

10. Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing.

11. Make sure an appliance mounted on a tank is securely installed before operating it.

12. Read and observe all the important notices on the appliance.

13. If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than

the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.

14. This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized

outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician. Never use with an extension cord unless plug can be fully inserted. Do not attempt to defeat this safety feature.

SAVE THESE INSTRUCTIONS

TWO YEAR LIMITED WARRANTY:

United Pet Group, a division of Spectrum Brands, Inc. (UPG), warrants this

Internal Filter against defects in material or workmanship for two years from the date of original purchase, subject to the

conditions and exceptions stated below. Your sales receipt is your Proof-of-Date-of-Purchase. If the Internal Filter exhibits

such a defect, UPG will repair or replace it, our option, without cost for parts or labor. The Internal filter must be shipped

postage paid to UPG. Proof-of-Date-of-Purchase is required. You are responsible for proper shipping. Call customer

service at 1-800-526-0650 for return authorization and shipping address. This warranty does not cover damage caused

by accident, misuse, abuse, or failure to follow the instructions accompanying this Internal Filter. All implied warranties,

including any implied warranty of merchantability or fitness for any purpose are limited to two year. Fish and plant loss,

personal injury, property loss or damage (direct, incidental or consequential) resulting from the use of the Internal Filter

are not covered by this warranty. Because some states/provinces do not allow the exclusion or limitation of incidental or

consequential damages, or allow limitations on how long an implied warranty lasts, the above limitations or exclusion

may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from

state/province to state/province.

APPLIANCE

AQUARIUM

POWER

CORD

DRIP

LOOP

Questions or Missing Parts?

Call Customer Service at

1-800-526-0650

Monday through Friday

8:00 AM to 5:30 PM ET

1 1 1

2 2 2

3 3 3

4 4 4

5-10i 10-30i 20-40i

Replacement Parts List

KEY

1

2

3

4

ITEM DESCRIPTION

Bio-Foam

®

Suction Cups

Impeller

Hanger Assembly

10-30i

25997

19613

19610

19632

5-10i

25996

19613

19609

19631

20-40i

25997

19613

19611

19632

MODEL NUMBER

Parts Diagram & Identification

Puntuación

Más sobre este manual

Entendemos que es bueno tener un manual en papel para tus Tetra Whisper 10-30i Filtro de acuario. Siempre puedes descargar el manual desde nuestro sitio web e imprimirlo tú mismo. Si deseas tener un manual original te recomendamos contactar con Tetra. Es posible que puedan proporcionar un manual original. ¿Estás buscando el manual de tu Tetra Whisper 10-30i Filtro de acuario en otro idioma? Elija su idioma preferido en nuestra página de inicio y busque el número de modelo para ver si lo tenemos disponible.

Especificaciones

Todos los manuales para Tetra Filtros de acuarios
Más manuales de Filtros de acuarios

Preguntas frecuentes sobre Tetra Whisper 10-30i Filtro de acuario

Nuestro equipo de atención al cliente busca información útil sobre los productos y responde a las preguntas frecuentes. Si encuentra inexactitudes en las preguntas frecuentes, indíquenoslo usando nuestro formulario de contacto.

Productos relacionados

Manual de uso

Tetra EX 1200 Plus Filtro de acuario

Manual de uso

Tetra EX 600 Plus Filtro de acuario

Manual de uso

Tetra EX 800 Plus Filtro de acuario

Manual de uso

Tetra Whisper 20-40i Filtro de acuario

Manual de uso

Tetra EX 400 Plus Filtro de acuario

Manual de uso

Tetra Whisper 5-10i Filtro de acuario

Manual de uso

Eheim Classic 1500XL Filtro de acuario

Manual de uso

Eheim Ecco Pro 2034 Filtro de acuario

Categorias relacionadas